SunSetter EASYSHADE Replacement

8 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

For Technical Support visit us at www.sunseer.com/ownerscorner

or Call Toll Free 800-670-7071 • Fax 877-224-4944

EASYSHADE®

Motorized EasyShade® Fabric Replacement

*Helper Needed*

Tools Needed:

Parts Supplied: 

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!

PLEASE READ THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE THIS PROCEDURE.

















1.

Cable Guide

Stop

Cable Guide

Bracket

Figure 1







EasyShade

Solar Screen

Vinyl Coated

Cable

Guide

Hole

Figure 2





Masking

Tape

Vinyl Coated

Cable

Figure 3

CAUTION: USE EXTREME CARE WHILE PERFORMING

STEP 6, TO ENSURE THE EASYSHADE DOES NOT

FALL FROM THE BRACKETS WHEN THE MOUNTING

SCREWS ARE LOOSENED. FAILURE TO USE CAUTION

CAN RESULT IN PERSONAL INJURY OR DAMAGE TO

THE EASYSHADE.





























Leading Bar

Leading Bar



Figure 4

Set Screw in Bracket

Other manuals for SunSetter EASYSHADE

Owner's Manual & Installation Instructions20 pages

Instructions8 pages

Owner’S Manual & Installation Instruction20 pages

Replacement Instructions4 pages

Assembly Instructions4 pages

Questions and Answers:

R
ruizrandyJul 28, 2025
Why does the SunSetter Indoor Furnishing fabric roll up unevenly?
- D
  David WalkerJul 28, 2025
  First, check that the aluminum housing is level on the mounting surface. Second, ensure the guiding cables are completely plumb. Both the aluminum housing and the cable brackets must be installed on the same vertical plane for the fabric to open and close smoothly. Check that the guiding cable is plumb front to back and left to right. You may need to move the cable brackets or shim them to ensure they are on the same vertical plane.
J
John HenryAug 2, 2025
What to do if the SunSetter Indoor Furnishing remote transmitter fails to open or close the EasyShade?
- T
  Tina WhiteAug 2, 2025
  First, verify the GFI electrical outlet is working. Second, test the remote transmitter (Channel 1) by pressing each button for 5 to 10 seconds; the LED light should blink for at least 5 seconds. If it doesn't, replace the remote's battery with a new Lithium CR2430. If power and the remote are good, consult 'Additional Motor Troubleshooting'.
S
Summer MoodyAug 6, 2025
How to replace the battery in the SunSetter Indoor Furnishing remote transmitter?
- C
  Cynthia BrownAug 6, 2025
  Here are the steps to replace the remote transmitter battery: 1. Remove and replace the remote transmitter’s battery with a new Lithium CR2430. * Remove the small Phillips screw on the back of the remote transmitter. * Remove the back cover. * Replace the old battery (note the battery orientation). * Reinstall the cover with the Phillips screw. 2. If the remote transmitter got wet: * Remove the back cover to allow it to dry completely. * Once dry, replace the back cover and try again.
J
jerryboltonAug 16, 2025
Why does the SunSetter Indoor Furnishing fabric appear folded or pleated?
- P
  Paula FloresAug 16, 2025
  Check the fabric to ensure it extends freely from the housing when the DOWN button is pressed. If the fabric remains in the housing while the motor turns, it can get pleated. To fix this, ensure the fabric doesn't stick inside the housing, especially in freezing conditions. Also, move the closed position so the sewn hem at the bottom of the fabric, where the aluminum leading bar is located, is just below the opening of the aluminum housing.

SunSetter EASYSHADE Specifications

General

Brand	SunSetter
Model	EASYSHADE
Category	Accessories
Language	English

Related product manuals

SunSetter EasyShade Series

SunSetter 1000XT

Preview: SunSetter 900XT

SunSetter 900XT

SunSetter VISTA

SunSetter Oasis

SunSetter Motorized

SunSetter Motorized Series

SunSetter Platinum Plus Series

SunSetter Platinum Series