Chapter 2: Installation
2-13
10G SAN MAC
BIOS LICENSE
+
1
1
+
DESIGNED IN USA
1G/10G MAC CODE
X10DRG-O+-CPU
REV:
1.00
IPMI CODE
BAR CODE
LD1
CLOSE 1st
OPEN 1st
CPU1
PCH
BMC
LAN
CTRL
LD2
JBT1
SW1
JITP1
J34
J33
JSPK1
JL1
JPB1
JPME2
JPL1
JVRM1
JPG1
JVRM2
J1
JPW22
JPW21 JPW24JPW23
JPW17JPW18
JPW14
JPW16
JPW15
JPW13
JPW3
JPW5
JPW7
JPW6
JPW12
JPW4
LE1
LE2
LEDM1
I-SGPIO1
I-SGPIO2
S-SGPIO
JTPM1
JF1
FAN4
FAN8
FAN3
FAN7
FAN2
FAN6
FAN5
FAN1
JSD2
JSD1
S-SATA3
S-SATA2
S-SATA1
S-SATA0
I- SATA5
I-SATA4
I- SATA3
I- SATA1
I- SATA2
I- SATA0
BT1
JPW10
JPP1
JPP2
J32
J31
CLOSE 1st
OPEN 1st
CPU2
USB7/8(3.0)
USB5/6(3.0)
USB4
P2 DIMMH3
P2 DIMMG3
P2 DIMME3
P2 DIMMF3
P1 DIMMC3
P1 DIMMD3
P1 DIMMA3
P1 DIMMB3
USB0/1
USB2/3
JWD1
JBR1
ON
RST
JF1
PWR
FAIL LED
PS
UID
2
NIC
1 LED
HDDNIC
LED
PWR
X
NMI
P1 DIMMC1
P2 DIMME1
COM1
P1 DIMMC2
P1 DIMMD1
P2 DIMME2
P1 DIMMD2
P2 DIMMF1
P2 DIMMF2
P1 DIMMB2
P2 DIMMH2
P1 DIMMB1
P1 DIMMA2
P2 DIMMH1
P1 DIMMA1
P2 DIMMG2
P2 DIMMG1
VGA
IPMI_LAN
LAN2
LAN1
Release Tabs
Notches
2-5 Installing and Removing the Memory Modules
Note: Check Supermicro's website for recommended memory modules.
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage.
Installing Memory Modules
1. Insert the desired number of DIMMs into the memory slots, starting with
P1-DIMMA1. (For best performance, please use the memory modules of the
same type and speed in the same bank.)
2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.
Removing Memory Modules
Press both notches on the ends of the DIMM module to unlock it. Once the DIMM
module is loosened, remove it from the memory slot.
3. Align the key of the DIMM module with the receptive point on the memory
slot.
4. Align the notches on both ends of the module against the receptive points on
the ends of the slot.
5. Use two thumbs together to press the notches on both ends of the module
straight down into the slot until the module snaps into place.
6. Press the release tabs to the locking positions to secure the DIMM module
into the slot.
Press both notches straight
down into the memory slot at
the same time.
To Next Page
Loading...
