Chapter 2: Installation
2-23
NIC1/NIC2 LED Indicators
The NIC (Network Interface Control-
ler) LED connection for LAN Port 1
is located on pins 11 and 12 of JF1,
and for LAN Port 2 is on pins 9 and
10. Attach the NIC LED cables here to
display network activity. Refer to the
table on the right for pin defi nitions.
HDD/UID LED
The HDD LED connection is located
on pins 13 and 14 of JF1. Attach a
cable here to indicate HDD activity
and UID status. See the table on the
right for pin defi nitions.
HDD LED
Pin Defi nitions (JF1)
Pin# Defi nition
13 UID LED
14 HD Active
1. HDD/UID LED
2. NIC1 LED
3. NIC2 LED
GLAN1/2 LED
Pin Defi nitions (JF1)
Pin# Defi nition
9 NIC 2 Activity LED
10 NIC 2 Link LED
11 NIC 1 Activity LED
12 NIC 1 Link LED
Power Button
OH/Fan Fail LED
1
NIC1 Link LED
Reset Button
2
Power Fail LED
HDD LED
PWR LED
Reset
PWR
3.3V
ID_UID_SW/3/3V Stby
Ground
Ground
19 20
3.3V
X
GroundNMI
X
NIC2 Link LED
NIC2 Activity LED
NIC1 Activity LED
UID LED
10G SAN MAC
BIOS LICENSE
+
1
1
+
DESIGNED IN USA
1G/10G MAC CODE
X10DRG-O+-CPU
REV:
1.00
IPMI CODE
BAR CODE
LD1
CLOSE 1st
OPEN 1st
CPU1
PCH
BMC
LAN
CTRL
LD2
JBT1
SW1
JITP1
J34
J33
JSPK1
JL1
JPB1
JPME2
JPL1
JVRM1
JPG1
JVRM2
J1
JPW22
JPW21 JPW24JPW23
JPW17JPW18
JPW14
JPW16
JPW15
JPW13
JPW3
JPW5
JPW7
JPW6
JPW12
JPW4
LE1
LE2
LEDM1
I-SGPIO1
I-SGPIO2
S-SGPIO
JTPM1
JF1
FAN4
FAN8
FAN3
FAN7
FAN2
FAN6
FAN5
FAN1
JSD2
JSD1
S-SATA3
S-SATA2
S-SATA1
S-SATA0
I- SATA5
I-SATA4
I- SATA3
I- SATA1
I- SATA2
I- SATA0
BT1
JPW10
JPP1
JPP2
J32
J31
CLOSE 1st
OPEN 1st
CPU2
USB7/8(3.0)
USB5/6(3.0)
USB4
P2 DIMMH3
P2 DIMMG3
P2 DIMME3
P2 DIMMF3
P1 DIMMC3
P1 DIMMD3
P1 DIMMA3
P1 DIMMB3
USB0/1
USB2/3
JWD1
JBR1
ON
RST
JF1
PWR
FAIL LED
PS
UID
2
NIC
1 LED
HDDNIC
LED
PWR
X
NMI
P1 DIMMC1
P2 DIMME1
COM1
P1 DIMMC2
P1 DIMMD1
P2 DIMME2
P1 DIMMD2
P2 DIMMF1
P2 DIMMF2
P1 DIMMB2
P2 DIMMH2
P1 DIMMB1
P1 DIMMA2
P2 DIMMH1
P1 DIMMA1
P2 DIMMG2
P2 DIMMG1
VGA
IPMI_LAN
LAN2
LAN1
To Next Page
Loading...
