Chapter 2: Installation
2-31
2-8 Jumper Settings
Explanation of Jumpers
To modify the operation of the motherboard,
jumpers can be used to choose between
optional settings. Jumpers create shorts be-
tween two pins to change the function of the
connector. Pin 1 is identifi ed with a square
solder pad on the printed circuit board. See
the board layout pages for jumper locations.
Note: On two-pin jumpers,
"Closed" means the jumper is on
and "Open" means the jumper is
off the pins.
Connector
Pins
Jumper
Cap
Setting
Pin 1-2 short
3 2 1
3 2 1
LAN Enable/Disable
JPL1 enables or disables Gigabit_LAN
ports 1/2 on the X10DRG-O+ and 10G_
LAN on the X10DRG-OT+. See the table
on the right for jumper settings. The default
setting is Enabled.
LAN Enable
Jumper Settings
Pin# Defi nition
1-2 Enabled (default)
2-3 Disabled
1. GLAN1/2 Enable
(X10DRG-O+)
1. GLAN1/2 Enable
(X10DRG-OT+)
10G SAN MAC
BIOS LICENSE
+
1
1
+
DESIGNED IN USA
1G/10G MAC CODE
X10DRG-O+-CPU
REV:
1.00
IPMI CODE
BAR CODE
LD1
CLOSE 1st
OPEN 1st
CPU1
PCH
BMC
LAN
CTRL
LD2
JBT1
SW1
JITP1
J34
J33
JSPK1
JL1
JPB1
JPME2
JPL1
JVRM1
JPG1
JVRM2
J1
JPW22
JPW21 JPW24JPW23
JPW17JPW18
JPW14
JPW16
JPW15
JPW13
JPW3
JPW5
JPW7
JPW6
JPW12
JPW4
LE1
LE2
LEDM1
I-SGPIO1
I-SGPIO2
S-SGPIO
JTPM1
JF1
FAN4
FAN8
FAN3
FAN7
FAN2
FAN6
FAN5
FAN1
JSD2
JSD1
S-SATA3
S-SATA2
S-SATA1
S-SATA0
I-SATA5
I- SATA4
I-SATA3
I- SATA1
I-SATA2
I- SATA0
BT1
JPW10
JPP1
JPP2
J32
J31
CLOSE 1st
OPEN 1st
CPU2
USB7/8(3.0)
USB5/6(3.0)
USB4
P2 DIMMH3
P2 DIMMG3
P2 DIMME3
P2 DIMMF3
P1 DIMMC3
P1 DIMMD3
P1 DIMMA3
P1 DIMMB3
USB0/1
USB2/3
JWD1
JBR1
ON
RST
JF1
PWR
FAIL LED
PS
UID
2
NIC
1 LED
HDDNIC
LED
PWR
X
NMI
P1 DIMMC1
P2 DIMME1
COM1
P1 DIMMC2
P1 DIMMD1
P2 DIMME2
P1 DIMMD2
P2 DIMMF1
P2 DIMMF2
P1 DIMMB2
P2 DIMMH2
P1 DIMMB1
P1 DIMMA2
P2 DIMMH1
P1 DIMMA1
P2 DIMMG2
P2 DIMMG1
VGA
IPMI_LAN
LAN2
LAN1
To Next Page
Loading...
