Supermicro X10SDV - Connecting Cables and Power Connectors

Chapter 2: Installation
2-19
BAR CODE
JTGLED1
X10SDV-TP8F
REV:1.01
DIMMB1
DIMMA2
DIMMB2
DIMMA1
BT1
LED3
C
LEDM1
A
C
LED8
C
LED7
A
C
JITP1
DESIGNED IN USA
COM1
1
PRESS FIT
JPS1
JPG1
JWD1
JPME2
JBR1
JPUSB1
JPL1
JPL2
JPME1
JPL3
JPTG1
JI2C2
JI2C1
JSMB1
JPB1
JNVI2C1
JIPMB1
LEDT4
A
C
LEDT2
A
C
LEDT3
A
C
LEDT1
A
C
LEDS1
A
MP_SRW1
MP_SRW2
JMP1
FAN4
FANA
FANB
FAN1
FAN3
FAN2
JSTBY1
JLANLED1
I-SGPIO1
I-SATA3
I-SATA2
I-SATA0
I-SATA1
JSD1
JSD2
JOH1
JL1
JTPM1
JF1
JSAS4
PRESS FIT
JSAS3
PRESS FIT
JSAS2
PRESS FIT
JSAS1
PRESS FIT
JPW1
JPI2C1
JD1
JGP1
JPH1
JPV1
M2_SRW2
M2_SRW3
M2_SRW1
VGA
LAN 7/8
LAN 5/6
LAN 3/4
LAN 1/2
JOH1-OH
SATA DOM + POWER
L-SAS12-15
L-SAS0-3
L-SAS4-7
L-SAS8-11
IPMI_LAN
2-3:DISABLE 1-2:ENABLE
JPUSB1:USB0/1 WAKE UP
2-3:DISABLE
LAN3/4/5/6
1-2:ENABLE
JPL3:
ON
PWR
RST
X
FF
OH
NIC2
JF1:
NIC1
LED
HDD
LED
PWR
PCI-E 2.0 X1 /
I-SATA5
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8
USB 5/6
USB 3/4
USB 2
USB 0/1(3.0)
PCI-E 3.0 X4 / I-SATA4
JMD1: M.2
Intel Xeon
D-1500
SoC
1-2:ENABLE
2-3:DISABLE
JPG1:
2-3:DISABLE
JPL1/JPL2:
1-2:ENABLE
JL1:
2-3:NMI
1-2:RST
JWD1:WATCH DOG
JBT1:
LAN2
LAN1/
CHASSIS
CMOS
INTRUSION
CLEAR
4-7:SPEAKER 1-3:PWR LED JD1:
1-2:ENABLE
2-3:DISABLE
JI2C1/JI2C2:
UID
1-2:ENABLE
2-3:DISABLE
JPS1:SAS
2-3:DISABLE 1-2:ENABLE JPTG1:
10Gb LAN
JBR1
1-2:NORMAL
2-3:BIOS RECOVERY
LSI
2116
(-7TP4F/-7TP8F)
BMC
AST2400
PHY
10GbE
CS2447
i350
AM4
(-7TP8F/
-TP8F)
2-6 Connecting Cables
This section provides brief descriptions and pin-out denitions for onboard headers
and connectors. Be sure to use the correct cable for each header or connector.
A. 24-Pin ATX Power
B. 12V 8-pin DC Power
C. 4-Pin HDD Power
ATX Power 24-pin Connector
Pin Denitions (JPW1)
Pin# Denition Pin # Denition
13 +3.3V 1 +3.3V
14 NC 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 NC 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
ATX PWR, DC PWR and HDD PWR
Connectors (JPW1, JPV1, JPH1)
The 24-pin ATX power connector at
JPW1 is used to provide power to the
motherboard. JPV1 is the 12V DC power
connector that provides alternative power
for special enclosure when the 24-pin
ATX power is not in use. The 4-pin HDD
power connector JPH1 provides power to
onboard HDD devices.
Note: Do not use the 8-pin DC
power at JPV1 when the 24-pin
ATX Power at JPW1 is con-
nected to the power supply. Do
not plug in both JPV1 and JPW1
at the same time.
C
B
A
1
4
1
4
5
8
4-Pin HDD Power
Pin Denitions (JPH1)
Pin# Denition
1 12V
2-3 GND
4 5V
8-pin DC Power
Pin Denitions (JPV1)
Pin# Denition
1-4 GND
5-8 12V