Supermicro X10SDV - LAN and SAS Port Enable;Disable Settings

2-32
X10SDV Flex ATX Series Motherboard User’s Manual
BAR CODE
JTGLED1
X10SDV-TP8F
REV:1.01
DIMMB1
DIMMA2
DIMMB2
DIMMA1
BT1
LED3
C
LEDM1
A
C
LED8
C
LED7
A
C
JITP1
DESIGNED IN USA
COM1
1
PRESS FIT
JPS1
JPG1
JWD1
JPME2
JBR1
JPUSB1
JPL1
JPL2
JPME1
JPL3
JPTG1
JI2C2
JI2C1
JSMB1
JPB1
JNVI2C1
JIPMB1
LEDT4
A
C
LEDT2
A
C
LEDT3
A
C
LEDT1
A
C
LEDS1
A
MP_SRW1
MP_SRW2
JMP1
FAN4
FANA
FANB
FAN1
FAN3
FAN2
JSTBY1
JLANLED1
I-SGPIO1
I-SATA3
I-SATA2
I-SATA0
I-SATA1
JSD1
JSD2
JOH1
JL1
JTPM1
JF1
JSAS4
PRESS FIT
JSAS3
PRESS FIT
JSAS2
PRESS FIT
JSAS1
PRESS FIT
JPW1
JPI2C1
JD1
JGP1
JPH1
JPV1
M2_SRW2
M2_SRW3
M2_SRW1
VGA
LAN 7/8
LAN 5/6
LAN 3/4
LAN 1/2
JOH1-OH
SATA DOM + POWER
L-SAS12-15
L-SAS0-3
L-SAS4-7
L-SAS8-11
IPMI_LAN
2-3:DISABLE 1-2:ENABLE
JPUSB1:USB0/1 WAKE UP
2-3:DISABLE
LAN3/4/5/6
1-2:ENABLE
JPL3:
ON
PWR
RST
X
FF
OH
NIC2
JF1:
NIC1
LED
HDD
LED
PWR
PCI-E 2.0 X1 /
I-SATA5
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8
USB 5/6
USB 3/4
USB 2
USB 0/1(3.0)
PCI-E 3.0 X4 / I-SATA4
JMD1: M.2
Intel Xeon
D-1500
SoC
1-2:ENABLE
2-3:DISABLE
JPG1:
2-3:DISABLE
JPL1/JPL2:
1-2:ENABLE
JL1:
2-3:NMI
1-2:RST
JWD1:WATCH DOG
JBT1:
LAN2
LAN1/
CHASSIS
CMOS
INTRUSION
CLEAR
4-7:SPEAKER 1-3:PWR LED JD1:
1-2:ENABLE
2-3:DISABLE
JI2C1/JI2C2:
UID
1-2:ENABLE
2-3:DISABLE
JPS1:SAS
2-3:DISABLE 1-2:ENABLE JPTG1:
10Gb LAN
JBR1
1-2:NORMAL
2-3:BIOS RECOVERY
LSI
2116
(-7TP4F/-7TP8F)
BMC
AST2400
PHY
10GbE
CS2447
i350
AM4
(-7TP8F/
-TP8F)
B A
A. JPL1
B. JPL2
C. JPL3
D. 10Gb LAN Ports Enable/Disable
10GbE LAN Ports Enable/Disable
JPTG1 is used to enable or disable 10GbE
support. See the table on the right for jumper
settings.
10Gb Enable/Disable
Jumper Settings
Pin# Denition
1-2 Enabled (Default)
2-3 Disabled
GbE LAN Ports Enable/Disable
Jumpers JPL1 and JPL2 are used to enable
or disable LAN ports 1 and 2, respectively.
Use JPL3 to enable or disable LAN ports 3,
4, 5, and 6. JPL3 is available on X10SDV-
7TP8F/TP8F only. See the table on the right
for jumper settings. The default setting is
enabled.
GbE LAN Enable
Jumper Settings
Pin# Denition
1-2 Enabled (Default)
2-3 Disabled
C
D