Supermicro X10SDV - CMOS Clear; PCI-E Slot SMB Enable; C1;I 2 C2)

2-28
X10SDV Flex ATX Series Motherboard User’s Manual
BAR CODE
JTGLED1
X10SDV-TP8F
REV:1.01
DIMMB1
DIMMA2
DIMMB2
DIMMA1
BT1
LED3
C
LEDM1
A
C
LED8
C
LED7
A
C
JITP1
DESIGNED IN USA
COM1
1
PRESS FIT
JPS1
JPG1
JWD1
JPME2
JBR1
JPUSB1
JPL1
JPL2
JPME1
JPL3
JPTG1
JI2C2
JI2C1
JSMB1
JPB1
JNVI2C1
JIPMB1
LEDT4
A
C
LEDT2
A
C
LEDT3
A
C
LEDT1
A
C
LEDS1
A
MP_SRW1
MP_SRW2
JMP1
FAN4
FANA
FANB
FAN1
FAN3
FAN2
JSTBY1
JLANLED1
I-SGPIO1
I-SATA3
I-SATA2
I-SATA0
I-SATA1
JSD1
JSD2
JOH1
JL1
JTPM1
JF1
JSAS4
PRESS FIT
JSAS3
PRESS FIT
JSAS2
PRESS FIT
JSAS1
PRESS FIT
JPW1
JPI2C1
JD1
JGP1
JPH1
JPV1
M2_SRW2
M2_SRW3
M2_SRW1
VGA
LAN 7/8
LAN 5/6
LAN 3/4
LAN 1/2
JOH1-OH
SATA DOM + POWER
L-SAS12-15
L-SAS0-3
L-SAS4-7
L-SAS8-11
IPMI_LAN
2-3:DISABLE 1-2:ENABLE
JPUSB1:USB0/1 WAKE UP
2-3:DISABLE
LAN3/4/5/6
1-2:ENABLE
JPL3:
ON
PWR
RST
X
FF
OH
NIC2
JF1:
NIC1
LED
HDD
LED
PWR
PCI-E 2.0 X1 /
I-SATA5
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8
USB 5/6
USB 3/4
USB 2
USB 0/1(3.0)
PCI-E 3.0 X4 / I-SATA4
JMD1: M.2
Intel Xeon
D-1500
SoC
1-2:ENABLE
2-3:DISABLE
JPG1:
2-3:DISABLE
JPL1/JPL2:
1-2:ENABLE
JL1:
2-3:NMI
1-2:RST
JWD1:WATCH DOG
JBT1:
LAN2
LAN1/
CHASSIS
CMOS
INTRUSION
CLEAR
4-7:SPEAKER 1-3:PWR LED JD1:
1-2:ENABLE
2-3:DISABLE
JI2C1/JI2C2:
UID
1-2:ENABLE
2-3:DISABLE
JPS1:SAS
2-3:DISABLE 1-2:ENABLE JPTG1:
10Gb LAN
JBR1
1-2:NORMAL
2-3:BIOS RECOVERY
LSI
2116
(-7TP4F/-7TP8F)
BMC
AST2400
PHY
10GbE
CS2447
i350
AM4
(-7TP8F/
-TP8F)
B
A
A. Clear CMOS
B. JI
2
C1
C. JI
2
C2
PCI Slot SMB Enable
Jumper Settings
Pin# Denition
1-2 Enabled
2-3 Disabled (Default)
PCI-E Slot SMB Enable (I
2
C1/I
2
C2)
Use jumpers I
2
C1/I
2
C2 to enable PCI
SMB (System Management Bus) support
to improve system management for the
onboard PCI-E slot. See the table on the
right for jumper settings.
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connec-
tion. Always remove the AC power cord from the system before clearing CMOS.
Note 1: For an ATX power supply, you must completely shut down the
system, remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2: Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3: Clearing CMOS will also clear all passwords.
C