What to do if my SWF E-Series Sewing Machine has trimming failure?
If your SWF Sewing Machine experiences trimming failure, it may be due to a poor connection or quality of the trimming solenoid (check and change the solenoid and solenoid connection), a bad connection (check connection), or a damaged trimming driver TR (change joint board).
What causes incorrect stop position on SWF E-Series?
An incorrect stop position on your SWF Sewing Machine can be due to loose tension on the main driver belt (adjust belt tension), or an incorrect position of the encoder or a bad encoder (adjust encoder position or change encoder).
What causes puckering on my SWF Sewing Machine?
Puckering on your SWF Sewing Machine can be caused by excessive thread tension (adjust tension), excessive pressure of the presser foot (change presser foot spring), needle failure such as a worn out or damaged needle tip (change needle), the needle being too large for the thread (use adequate size of needle), or the needle hole being too large for the needle.
What causes needle breaks on my SWF Sewing Machine?
Needle breaks in your SWF Sewing Machine can occur due to: a bent needle (change needle), a bad quality needle (space the needle and the hook point), the tip of the needle being worn or bent (correct the installation), the needle touching the hook point (check if needle plate is unscrewed), incorrect installation of the needle (adjust the position of the needle bar), or the needle touching the needle hole on the plate.
What causes poor stitch tension on my SWF E-Series Sewing Machine?
Poor stitch tension in your SWF Sewing Machine can be attributed to: weak upper thread tension (adjust tension), uneven upper thread tension due to foreign substances (clean main and sub tension adjusters in the thread tension adjusting plate), weak lower thread tension (adjust tension), uneven lower thread tension (clean bobbin case and check tension on bobbin spring), thread thickness (change to quality thread), poor timing of needle and hook (adjust timing), or insufficient oil in hook (oil the raceway of hook).
What causes bad stitch quality on SWF E-Series Sewing Machine?
Bad stitch quality on your SWF Sewing Machine can stem from several causes: bad tape (correct tape), inadequate tension on the X-Y belt (adjust tension), foreign substance in the X-Y rail (clean the rail), failure of the X/Y driver board (change circuit board), or a heavy load on the frame (reduce speed of main shaft).
What to do if my SWF E-Series has bad color change?
If your SWF Sewing Machine has a bad color change, it could be due to several factors. Refer to the user’s manual, run a manual color change, and check if the signal lamps (needle set lamp & needle position lamp) blink at the correct needle position. Adjust the half-turn film. Other potential causes include an incorrect position of the needle bar (set it to the correct position), an incorrect position of the take-up lever (adjust so take-up lever is in line with other levers in stop position, upper shaft angle: 100°), or a bad connection (change fuse F3 in the joint board or check the connection).
Why is my SWF E-Series Sewing Machine showing operation failure?
Operation failure in your SWF Sewing Machine can be due to several reasons: loose belt tension or belt damage (adjust belt tension or change the belt), power failure or short-circuit of fuse (check and change the fuse in the main shaft motor), or failure to sense signals for needle position or 1 rotation (run manual color change and check if signal lamps blink at the correct needle position, adjust the half-turn film, address the cause and press RESET, then check if the lamp turns green). Also, check the connection of the START switch.
Guidance on resolving common problems encountered during operation.
Methods for setting the correct upper thread tension for quality stitches.
Correctly threading the bobbin and setting its tension.
Details on needle types, selection, and interaction with the hook.
Importance of correct timing between needle and hook for stitch quality.
Key points to check during routine machine inspections for upkeep.
Where and how often to apply oil for machine lubrication.
Where and when to apply grease for component lubrication and wear prevention.
How to adjust the thread trimmer for optimal cutting performance.
General| Type | Embroidery Machine |
|---|---|
| Needle Threader | Automatic |
| Maximum Speed | 1, 000 SPM |
| Data Input | USB |
| Power Supply | 220V, 50/60Hz |
| Speed Control | Adjustable |
| Heads | Single head |
To Next Page
