Need help?Do you have a question about the Symcode BROCHURE and is the answer not in the manual?
General| Brand | Symcode |
|---|---|
| Model | BROCHURE |
| Category | Barcode Reader |
| Language | English |
Introduces the 2D desktop barcode scanner, its patented technologies, and target audience.
Details the scanner's independent R&D, plug-and-play, wide voltage design, chip, and interfaces.
Details dimensions, weight, power voltage, and current consumption of the scanner.
Specifies light source, image resolution, and supported interfaces for the scanner.
Outlines operating temperature, humidity, ambient light, and drop/ESD resistance.
Lists supported 1D and 2D barcode symbologies and their decode ranges.
Illustrates the physical layout of the scanner, highlighting scan window, button, buzzer, and ports.
Explains how to restore the scanner to its original factory default settings by scanning a barcode.
Covers RS232 serial connection, baud rate, data bits, stop bits, and parity settings.
Describes USB HID Keyboard and USB COM emulation modes for scanner connection.
Briefly introduces the chapter's focus on scanner output configurations and feedback.
Allows enabling or disabling the buzzer sound when the scanner is powered on.
Controls the buzzer sound when a barcode is successfully decoded.
Adjusts the volume level of the scanner's buzzer for successful decodes.
Sets the frequency of the buzzer sound for successful barcode decodes.
Chooses between a normal or short beep sound upon successful barcode decoding.
Configures the delay time between consecutive barcode scans.
Controls the scanner's illumination or aiming light, with ON/OFF options.
Manages the scanner's power-saving standby mode duration.
Allows adding custom prefixes or suffixes to barcode data for specific or all code types.
Specifies the characters (CR, LF, CR+LF) to be appended after scanned data.
Configures how the scanner interacts with keyboard input and operations.
Enables or disables the transmission of function characters embedded in barcode data.
Sets a delay for data transmission after a barcode scan.
Allows enabling or disabling all supported barcode symbologies simultaneously.
Defines minimum and maximum length constraints for barcode decoding to reduce errors.
Options to enable or disable all 1D barcode symbologies.
Options to enable or disable all 2D barcode symbologies.
Configuration for Codabar barcode symbology, including enable/disable, start/stop bits, check bits, and cascade.
Settings for Code 39 barcodes, including enable/disable, start/stop bits, and check bits.
Settings for Code 32 (PARAF) barcodes, requiring Code 39 to be enabled first.
Configuration for Interleaved 2 of 5 barcodes, including enable/disable and check bits.
Settings for NEC 2 of 5 barcodes, including enable/disable and check bits.
Configuration for Code 93 barcodes, including enable/disable and decode length settings.
Settings for Straight 2 of 5 Industrial barcodes (three-bar start/stop).
Settings for Straight 2 of 5 IATA barcodes (two-bar start/stop).
Configuration for Matrix 2 of 5 barcodes, including enable/disable and decode length.
Settings for Code 11 barcodes, including enable/disable, check bits, and decode length.
Configuration for Code 128 barcodes, including enable/disable and decode length.
Settings for ISBT 128 Cascade, including enable/disable and decode length.
Configuration for UPC-A, including enable/disable, check bits, digital system, and supplementals.
Enables reading UPC-A with supplemental data, requiring 2 or 5 supplementals to be enabled.
Defines the separator behavior between normal data and supplemental barcode data.
Configuration for GS1-128, including enable/disable and decode length.
Settings for UPC-E0, including enable/disable, barcode expand, and supplementals.
Configuration for UPC-E1, including enable/disable and check bits.
Settings for EAN/JAN-13, including enable/disable, check bits, and supplementals.
Configuration for EAN/JAN-8, including enable/disable and check bits.
Settings for MSI, including enable/disable and check bits.
Configuration for GS1 DataBar Omnidirectional, including enable/disable.
Settings for GS1 DataBar Limited, including enable/disable.
Configuration for GS1 DataBar Expanded, including enable/disable and decode length.
Settings for PDF417, including enable/disable and decode length.
Configuration for Data Matrix, including enable/disable and decode length.
Settings for QR Code and Micro QR Code, including enable/disable and decode length.
Configuration for Aztec Code, including enable/disable and decode length.
Settings for China Post (Hong Kong 2 of 5), including enable/disable.
Configuration for Korea Post, including enable/disable and decode length.
Settings for Han Xin Code, including enable/disable and decode length.
Configuration for Maxi Code, including enable/disable and decode length.
Settings for Micropdf, including enable/disable and decode length.
Configuration for GS1 Composite Code, including enable/disable and decode length.
Settings for Codablock A, including enable/disable and decode length.
Configuration for Codablock F, including enable/disable and decode length.
Displays the scanner's software version information on the terminal.
Allows mirroring the scanned image horizontally or vertically.
Enables reading barcodes printed with reversed colors (white on black).
Sets the scanner to operate in a safe mode, potentially limiting certain functions.
Configures settings related to QR codes and website links.
Adds a prefix, such as a serial number, to the scanned barcode data.
Allows selecting the keyboard language layout for scanner output.
Enables and configures the Chinese keyboard input mode for the scanner.
Sets the output format for Chinese characters (GBK or UNICODE).
Controls the case sensitivity (lowercase, uppercase, swap) of scanned characters.
Provides answers to common questions and solutions for scanner operational issues.
Offers guidance on cleaning and maintaining the barcode scanner for optimal performance.
To Next Page
