How to fix a Symmons Temptrol II valve that leaks when shut off?
If your Symmons Plumbing Product valve leaks when shut off, the hot and cold washers are likely worn, or there's foreign matter (like solder or chips) between the washers and seat surfaces. Replace the hot and cold washers, and inspect the top surface on the hot and cold seats, replacing them if necessary.
Why does my Symmons Temptrol II valve deliver hot water initially and then turn cold?
If your Symmons Plumbing Product valve delivers hot water when initially opened, and the water turns colder when rotating the handle counter-clockwise, it might be due to incorrect piping. The hot supply may be connected to the cold inlet, and vice versa. If you can access the piping, correct the connections. If not, contact the factory to order a reverse seat and tool (T-108 Kit). Older installations might also need a hot seat replacement (T-1).
What to do if temperature varies without moving handle on Symmons Temptrol II Plumbing Product?
If the temperature from your Symmons Plumbing Product varies without you moving the handle, it's likely that the pressure balancing piston inside the spindle assembly is blocked by foreign matter. Follow these steps: With the valve open halfway, remove the handle and gently tap the spindle using a plastic hammer. If the issue persists, completely remove the spindle assembly and tap the handle end against a solid object to dislodge the piston. Soaking the assembly in household vinegar can also help dissolve any foreign matter.
Why is the water volume inconsistent when adjusting the temperature on my Symmons Temptrol II Plumbing Product?
If the temperature control handle of your Symmons Plumbing Product is turned from cold to hot (or hot back to cold) and the water volume from the spout or head isn't consistent, it's probably because the pressure balancing piston in the spindle assembly is blocked by foreign matter. With the valve open halfway, take off the handle and tap the spindle with a plastic hammer. If that doesn't work, fully remove the spindle assembly and tap the handle end against something solid to free the piston. You can also try soaking it in household vinegar to dissolve any debris.
Why does my Symmons Temptrol II have low hot water pressure?
If your Symmons Plumbing Product valve delivers sufficient cold water but little hot water (or the reverse), the pressure balancing piston housed in the spindle assembly may be blocked by foreign matter. With the valve open halfway, remove the handle and tap the spindle with a plastic hammer. If the problem is not resolved, remove the spindle assembly completely and tap the handle end against a solid object to free the piston. Soaking it in household vinegar can also help remove any foreign matter.
What to do if Symmons Temptrol II Plumbing Product temperature reduces gradually during use?
If the delivery temperature of your Symmons Plumbing Product valve gradually decreases during use, requiring you to turn the handle to hotter positions to maintain a constant temperature, you may be experiencing an overdraw on the hot water supply, meaning you are running out of hot water. To fix this, reduce the maximum flow by adjusting the volume control on the valve or showerhead. This will allow for a longer period of use before the hot water supply is depleted.
Why won't my Symmons Temptrol II valve pass water?
If your Symmons Plumbing Product valve will not pass water, ensure that both the hot and cold water supplies are turned on. The valve will not operate unless both hot and cold water pressure are active.
What to do if the Symmons Control Unit temperature handle affects water volume?
If the temperature control handle is turned from cold to hot (or vice versa) and the water volume from the spout or head isn't constant, the pressure balancing piston in the spindle assembly may be blocked by foreign matter. With the valve open halfway, remove the handle and tap the spindle with a plastic hammer. If that doesn't work, remove the spindle assembly completely and tap the handle against a solid object to free the piston. Soaking it in household vinegar can also help dissolve any foreign matter.
Why does the Symmons Control Unit temperature gradually reduce during use?
If the valve delivery temperature reduces gradually during use, requiring you to turn it to hotter positions to maintain a constant temperature, it's likely due to an overdraw on the hot water supply. To resolve this, reduce the maximum flow by using the volume control adjustment on the valve or shower head. This will allow for a longer period of use before overdrawing the hot water supply.
What to do if Symmons Control Unit valve leaks when shut off?
If the Symmons Control Unit valve leaks when shut off, the hot and cold washers may be worn, or foreign matter (like solder chips) may be trapped between the washers and seat surfaces. You should replace the hot and cold washers and inspect the top surface on hot and cold seats, replacing them if necessary.
General guide to the valve's functionality and maintenance procedures.
Explains the warranty terms and conditions for the product.
Instructions for setting the limit stop screw and important safety warnings.
Lists necessary tools and specifies rough-in dimensions for wall installation.
Details how to connect piping for shower heads and tub spouts.
Steps for preparing the wall and securing the valve body.
Includes limit stop screw setting and system flushing.
Guidance for installing valves on opposite sides of a wall.
How to control temperature and water flow with the handle.
Proper methods for cleaning and maintaining the valve's finish.
Specific procedures for mounting the valve in non-traditional wall materials.
Details tools and steps for replacing hot and cold valve seats.
Addresses problems like no water flow or leaks with solutions.
Enumerates individual components and their part numbers.
Lists pre-assembled part kits and their associated components.
General| Model | Temptrol II |
|---|---|
| Material | Brass |
| Maximum Pressure | 125 psi |
| Warranty | Limited Lifetime |
| Inlet Connection Size | 1/2 inch |
| Outlet Connection Size | 1/2 inch |
| Temperature Control | Pressure Balancing |
| Maximum Temperature | 180°F |
| ADA Compliant | Yes |
| Finish | Chrome |
To Next Page