25
Synrad Firestar OEM v30 reference guide
Firestar OEM v30 general specifications
Table 7 Firestar OEM v30 specifications
Parameter
Output Specifications 10.6 µm 10.2 µm 9.3 µm
Wavelength
†
..................................................10.57–10.63 microns ......... 10.20–10.30 microns ........ 9.23–9.31 microns
Power Output, continuous
1, 2
.........................30 W..................................25 W .................................20 W
Power Stability
3
.............................................±5% ................................... ±5% ...................................±7%
Power Stability
4
.............................................±3% ................................... ±3% ...................................±5%
Mode Quality (M
2
) ........................................ < 1.2 .................................< 1.4 .................................. < 1.3
Beam Waist Diameter (at 1/e
2
)
5
.....................2.5 mm ±0.5 mm ............... 2.5 mm ±0.5 mm .............2.5 mm ±0.5 mm
Beam Divergence, full angle (at 1/e
2
) ............< 7 mrad ............................< 7 mrad ............................< 7 mrad
Ellipticity .......................................................< 1.2 ..................................< 1.2 .................................. < 1.2
Polarization ...................................................Linear, horizontal ..............Linear, horizontal ..............Linear, horizontal
Rise Time ......................................................< 100 µs ............................. < 100 µs .............................< 100 µs
Input Specifications
Power Supply
Voltage ........................................... 30 ±2.0 VDC
Current, max. (air-/water-cooled) . 15 A (24 A peak for 0.5 ms minimum)
(fan-cooled) ........... 16 A (24 A peak for 0.5 ms minimum)
Input Signals Tickle Signal ........................................... PWM Command Signal
Voltage ................. +3.5 to +6.7 VDC (5V nominal) ................+3.5 to +6.7 VDC (5V nominal)
Current ................10 mA @ +6.7 VDC ....................................10 mA @ +6.7 VDC
Pulse Duration ......1 µs ...............................................................N/A
Frequency .............5 kHz ............................................................DC–100 kHz
Cooling Specifications (Air-/fan-cooled) (Water-cooled)
Maximum Heat Load, laser ................... 450 Watts .................................450 Watts
Minimum Flow Rate ............................. 140 CFM per fan (×2) ..............1.0 GPM, < 60 PSI
Coolant Temperature ............................. < 40 °C, ambient .....................18–22 °C
Environmental Specifications
Operating Temperature
6
....................... 15 °C–40 °C
Humidity ............................................... 0–95%, non-condensing
Physical Specifications (Air-cooled) (Fan-cooled) (Water-cooled)
Length ..................................... 16.79 in (42.65 cm) ..................16.79 in (42.65 cm) .................17.06 in (43.33 cm)
Width ...................................... 4.58 in (11.63 cm) .................. 4.72 in (11.94 cm) ................. 4.58 in (11.63 cm)
Height ..................................... 5.76 in (14.63 cm) .................. 6.28 in (15.95 cm) ................. 5.84 in (14.83 cm)
Weight .....................................18.00 lbs ( 8.20 kg) ................... 21.30 lbs ( 9.66 kg) ..................19.24 lbs ( 8.73 kg)
* Specifications subject to change without notice.
† Typical. Actual wavelength range may vary from 10.2–10.8 µm.
1 This power level is guaranteed for 12 months regardless of operating hours.
2 Minimum 30 VDC input voltage to obtain guaranteed output power.
3 From cold start (guaranteed) at 95% duty cycle.
4 After two minutes (typical) at 95% duty cycle.
5 Measured at laser output.
6 Published specifications guaranteed at a temperature of 22 °C. Some performance degradation may occur in ambient temperatures above 22 °C. Typically,
laser output power decreases 0.5–1% per degree Celsius increase in ambient temperature.