15
Device Preferences > Factory data reset
and press
OK
to enter.
2.
Press
▲/▼
to select
Factory data reset
and press
OK
to enter. Then select
Erase everything
and
press
OK
to confirm.
3.
Enter 1234 or the PIN according to the on-screen
prompt.
4.
Select
OK
and press
OK
to conrm.
5.
The
Pair Your Remote
page appears. Follow the
instructions in the section
Initial setup
.
Password in Parental Control
-
The default password is 1234. You can change it to a
new one.
-
The super password is 0423. If you forget your code,
enter the super password to override any existing
codes.
Using the Hands-free TV Voice Control
(* not available for some models)
Before using the hands-free TV voice control, connect the
TV to the network and make sure it can access the Goo-
gle website rst. Then follow the steps below to access.
1. Turn the built-in MIC switch (next to the power button)
to on before using this function.
2. Access the Android TV homepage by pressing on
the remote control.
3. Select
(Settings) > Device Preference > Google
Assistant >On
and
press
OK
to turn it on. Follow the
on-screen guide to nish your settings for the rst time.
4. Say “OK Google” to activate it.
Notes:
-
The availability of hands-free TV voice control
depends on your region/country/language and your
model. For details, please refer to your local dealer.
-
A quiet surrounding is required for better function
when using it. The recommended using distance is
within 2 meters in front of TV set.
-
Turn the built-in MIC switch to off if you are not going
to use it. Or set
(Settings) > Device Preference >
Google Assistant > On to off.
-
Standby power consumption will increase because
the built-in MIC is always listening when the Google
Assistant or voice control with the built-in MIC is
enabled.
-
It is recommended to set (Settings) > Device
Preference > Google Assistant > On to off to avoid
interference when there are two or more terminals
using the Google Assistant function at the same time.
Multi Visual
Allows you to enjoy different programmes with your fami-
ly on one TV at the same time.
The multi visual function is enabled by default. To use the
Using more of your TV
function, make sure your phone is Android OS and the
WiFi on the phone is turned on. Then follow the steps
below to operate.
1.
Press
on the remote control, select
(Settings)
>
Network & Internet >
Wi-Fi
,
and press
OK
to turn
it on.
2.
Activate
the cast screen function on your phone and
choose the TV’s name you want to connect in the
searching list.
3.
For the rst time, depending on different types of
phones, there are two situations: 1) an invitation
prompt appears, select "
Accept
" and press
OK
to
connect. 2) enter a correct PIN code to connect as
per the PIN message on the phone.
4.
Then dual views display and you can enjoy different
programmes at the same time.
5.
If you want to watch only one programme, use ◄/►
to select your desired view and press
OK
to enter
the full screen.
6.
To return to the previous dual view screen, press
and hold on the remote control.
7.
To exit the multi visual function, press to display a
dialog box, then select
OK
and press
OK
to conrm.
Notes
:
-
This feature is not available in any of the cases
below:
a) when TV is in Netlx or Media Player.
b) if the video from phone/DTV is scrambled.
c) when the capacity of required video decoding
exceeds 4K 60Hz.
-
When in full screen mode, due to the compatibility
of the third party’s Apps, there might occur failure to
return to the dual views.
-
At most 2 phones can be casted to the TV at the
same time. When in dual view mode, use ◄/► to
move the focus to TV view and then cast another
phone to the TV.
-
To disable the feature, select
(Settings) > Device
Preferences > Multi visual settings > Multi visual
and press
OK
to turn it off.
-
To check all available history list, select
(Settings)
> Device Preferences > Multi visual settings >
Connection list
and press
OK
to enter.
To Next Page
Loading...
Need help?
General
