Technics SL-MC7 User Manual

Reference
Troubleshootin g guide
Before requesting service for this unit, check the chart below for a
possible cause of the problem you are experiencing. Some simple
checks or a minor adjustment on your part may eliminate the prob¬
lem and restore proper operation.
If you are in doubt about some of the check points, or if the reme¬
dies indicated in the chart do not solve the problem, refer to the
directory of Authorized Service Centers (enclosed with this unit) to
locate a convenient service center, or consult your dealer for
instructions.
For detailed instructions, contact an authorized servicenter in
the U.S.A. and Panasonic Canada Inc. Customer Care Centre in
Canada.
In the U.S.A. 1-800-211-7262 or web site
(http://www.panasonic.com)
In Canada 905-624-5505 or web site
(www.panasonic. ca/faq. html)
Reference pages indicated in black circles. (For example: O)
Problem
Suggested remedy
Changer will not play.
A disc(s) or other foreign object(s) has fallen
inside the changer. '
• Open the front panel and remove the object.
Moisture has collected in the changer. i
1
• Allow the changer to dry out for about one hour
before using it.
The disc in the changer
The disc label is facing left, , • Set the disc with the label facing right. (0)
does not play.
The disc is dirty.
• Wipe the disc with a soft cloth. (®)
The disc is scratched.
• Replace the disc with a new one.
The disc is warped.
1
The disc is not within specified standards.
Play stops before changing
to the next disc.
The front panel is open.
• Close the panel.
A certain music passage
The disc is dirty.
• Wipe the disc with a soft cloth.(®)
can’t be played correctly.
The disc is scratched. I
• Replace the disc with a new one.
There is noise from the
tuner or disturbance on the
TV screen.
Caused by high-frequency signals from this
changer, I
• Use the changer further away from the tuner or TV.
• If the tuner or TV's antenna is the indoor type, use
an outdoor one.
The error message “NO
PGM’’ appears on the dis¬
play, when program play is
started.
Play was started without a track being pro- '
grammed. i
• Program a track. (®)
The error message
“ERROR” appears on the
display, and the changer
stops operating.
The mechanism of the changer has been improp- ^
erly adjusted. |
• Turn the unit off and then back on again.
The error message “F-26”
appears on the display and
the changer stops operat¬
ing.
The servo LSI has malfunctioned. !
I
• Unplug the changer from its outlet, replug it in and
turn the changer ON again.
The error message “TAKE
OUT” appears on the dis-
A disc has been put in the slot of the disc in play. '
• Remove the disc whose number is displayed and
press the stop button.
play and the changer stops
operating.
Because of light or noise, the changer has detect¬
ed a disc in the slot of the disc being played, even
though it is empty.
• Check whether there is a disc in the displayed slot.
With the front panel closed, hold down [ ■ ] for at
least 4 seconds.
The changer does not
The batteries have run out.
• Replace batteries with new ones.
respond correctly to remote
commands.
There is an obstruction between the remote con¬
trol and the changer.
• Remove the obstruction.
The batteries are inserted incorrectly,
[The (+) and (-) polarities are reversed.]
• Reinsert batteries so that the polarities are correct.
Maintenance
If the surfaces are di
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a soap-
and-water solution or a seak ditergent solution.
ROT4941
• Never use alcohol, paint thinner or benzine to clean this unit.
• Before using chemically impregnated cloth, read the instructions
that came sith athe cloth carefully.

Technics SL-MC7 Specifications

General

Brand	Technics
Model	SL-MC7
Category	CD Player
Language	English