Tecnologic THP 98 User Manual

0000 ... 9999Password request second level
programming parameters
PASS
SECOND LEVEL PARAMETERS TABLE
10 ... 20 sec.Input digital filter costant
FiLt
0-999 ... 9999
-99.9 ... 999.9
Calibration
OFFt
J J / CrAl / r / S
/ t Pt1 / Pt2
Input probe
SEnS
CC / F / AbSUnit of measurement
Unit
50-100.0 ... 100.0
%
Manual reset
rS
301 ... 255 sec.Output C2 cycle time
tcr2
100.0 ... 999.9C2 / C1 power ratio
Prat
301 ... 255 sec.Output C1 cycle time
tcr1
300 ... 9999 sec.Derivative time
dEr
5000 ... 9999 sec.Integral time
Int
1001 ... 9999Proportional band
Pb
nono / SP / LoSPAutotuning
Auto
HEAtHEAt / CooLOutput C1 operating mode
Func
PidPid / OnOFControl mode
Con1
9999SPLL ... 9999
SPLL ... 999.9
High/maximum Set point
SPHL
-999-999 ... SPHL
-99.9 ... SPHL
Low/minimum Set Point
SPLL
nono / yESAlarm programming at first or
second level parameters
ALPr
nono / yESDisconnection of alarm A2
dAL2
nono / yESDisconnection of alarm A1
dAL1
norL1 - rL2
rL12 - no
Alarm on for error instrument
FAIL
nOnO - nCOutput HB logic mode
rLHb
00000000 ... 5111Alarm A2 operation mode
rL2
00000000 ... 5111Alarm A1 operation mode
rL1
NotesDef.RangeDescriptionPar.
7 - PROBLEMS, MAINTENANCE AND WARRANTY
ERRORS SIGNALLING : The 2 displays are used as well to visualise
anomaly conditions of instrument functioning :
- In case of probe interruption it's visualised "- - - -" flashing.
- In case the measured variable goes under the probe limits it's visualised
"uuuu" flashing.
- In case the measured variable goes upper under the probe limits it's
visualised "oooo" flashing.
In these cases verify the correct connection of the probe with the
instrument and afterward proceed to verify the probe itself.
- In case the Autotuning has been interrupted by an anomaly (probe
interruption, etc.) it's visualised "no Auto" flashing.
- In case the Autotuning is not ended within 4 hours, it's visualised "tout
Auto" flashing.
- If the instrument has been switched-off during the programming, at the
next switching-on will be signalised the eeprom memory error, appearing
the message "Err EEPr". To re-establish the right functioning it's
necessary to push contemporary the "P" and "LEFT" keys and then get into
parameter programming of the first level, go out regularly, even if no
parameters are changed.
All the anomaly conditions will de-active all the regulation outputs.
HOW TO CLEAN: We recommend to avoid abrasive cleaners or
containing solvents which could damage the instrument.
WARRANTY AND REPAIRS: The instrument is under warranty against
construction vices or defected material, noticed within 12 months from
delivery date.The warranty is limited to the repairs or to the substitution of
the instrument. The eventual opening of the housing, the violation of the
instrument or the wrong use and installation of the product means the
automatically decay of the warranty. In case of defected instrument,
noticed in warranty period or out of warranty, do contact our sales
department to obtain the shipment authorisation. The defected product
must be shipped to TECNOLOGIC with the detailed description of the
failures found and without any fees or charge for Tecnologic, safe
different agreements.
THP 98 PASSWORD = 0381
TECNOLOGIC - THP 98 USER MANUAL (I - GB) - Vr. 01 - ISTR 00372 - PAG. 12

Tecnologic THP 98 Specifications

General

Brand	Tecnologic
Model	THP 98
Category	Controller
Language	English