What to do if the Teldat Network Router loses date and time settings?
If your Teldat Network Router is losing date and time settings after restarting, it is recommended to use the NTP protocol to maintain accurate date and time.
What to do if the S LED is red on Teldat Network Router?
If the S LED on your Teldat Network Router is red: * Ensure that the SIM card is inserted correctly. * Verify that the SIM PIN is correct. * Check if the antenna has been properly installed by ensuring it has been screwed in correctly. * Have your technical service validate that the device is in the optimal position for the service.
What to do if LAN, WAN, SFP or SW LEDs fail to light up in green on Teldat Network Router?
If the LAN, WAN, SFP, or SW LEDs on your Teldat Network Router fail to light up in green, inspect the Ethernet cable, fiber connection, and network connection. A crossover cable may be required.
What to do if the local console is unresponsive on Teldat Network Router?
If the local console is unresponsive on your Teldat Network Router: 1. Ensure that the correct console cable is being used and that it is properly connected to both the device and the asynchronous terminal. 2. Verify that the terminal is configured with the correct port. 3. Verify that the terminal configuration is 115200 8N1. 4. Check that the console is not being used for event processing.
Why is the local console displaying irrelevant information on Teldat Network Router?
If the local console on your Teldat Network Router is displaying irrelevant information, verify that the terminal is configured with the correct port and that the terminal configuration is 115200 8N1.
How to troubleshoot Teldat Network Router when none of the LEDs are lighting up?
If none of the LEDs on your Teldat Network Router are lighting up, verify the power supply to the router, including the power source and main power outlet.
Why does the Teldat Network Hardware lose date and time after restart?
If the date and time are lost in your Teldat Network Hardware device after a restart, it's because parameters configured through the time set command are not persistent. To resolve this, use the NTP protocol to maintain the correct date and time configuration.
What to do if I forgot the Teldat Regesta Smart PRO Network Hardware access password?
If you've forgotten the access password for your Teldat Network Hardware router, ignore the current configuration by using the RST button, as detailed in the relevant section of the manual.
Why is the S LED red on my Teldat Regesta Smart PRO Network Hardware?
If the S LED on your Teldat Network Hardware is red, check the SIM card to ensure it's correctly inserted and that the SIM PIN is correct. Also, verify that the antenna is properly installed. If issues persist, your technical service may need to check if the device is optimally positioned for service.
What to do if LAN, WAN, SFP, or SW LEDs don't light up green on Teldat Regesta Smart PRO Network Hardware?
If the LAN, WAN, SFP, or SW LEDs on your Teldat Network Hardware do not light up in green, check the Ethernet cable or fiber connection to the network. You might need a crossover cable to establish the connection.
Details the front panel, including status LEDs and their meanings.
Important conditions for installing the equipment safely and correctly.
Step-by-step guide to remove and install the connector protective casing.
Details on how to connect the router to a power source.
Explains the power connector and its pins for DC and AC power.
Overview of various data connection types available on the router.
Details the Gigabit Ethernet LAN port and its specifications.
Describes the WAN interface, including SFP and RJ-45 connectors.
Information on connecting WWAN antennas for cellular connectivity.
Overview of serial port connections available on the router.
Provides solutions for common installation and operational issues.
General| Connectivity Technology | Wired, Wireless |
|---|---|
| Frequency Band | 2.4 GHz, 5 GHz |
| Security Protocols | WPA, WPA2, WPA3 |
| Type | Router |
| WAN | 1 x 10/100/1000 Mbps |
| LAN | 4 x 10/100/1000 Mbps |
| Wi-Fi | 802.11a/b/g/n/ac |
| Cellular | 4G LTE |
| Power Supply | 12V DC |
| Device Type | Router |
| Wireless Standards | IEEE 802.11a/b/g/n/ac |
| Firewall | Stateful Packet Inspection (SPI) |
| Management Interface | CLI |
To Next Page