To Next PageTo Next Page
Need help?Do you have a question about the Teleco TVDMM868A05 and is the answer not in the manual?
Details terminal connections for high voltage and low voltage inputs/outputs.
Indicates output selection via P4 button or radio transmission.
Configuration options for PIR sensor output selection.
Dip-switch settings for controlling load characteristics.
LEDs indicating overload or overtemperature faults.
Configures load type and functioning mode (switching/dimming).
Sets PIR sensor activation time for all outputs.
Procedure to memorize 7/42 channel transmitters for scenes and dimming.
Memorizes a single button for ON/OFF and Dimming function.
Memorizes a button for ON function, retaining last output level.
Memorizes a button for OFF function, turning the load off.
Memorizes 3-channel transmitters for dimming and ON/OFF.
Memorizes Green Mouse for automatic light control.
Memorizes 4-channel transmitters for preset scene selection.
Memorizes a button for ON-OFF function with short pulses.
Memorizes wireless PIR sensors for automatic load activation.
Procedure to disable or enable transmitter buttons.
Modifies preset scenes for a transmitter associated with a single output.
Identifies outputs for preset scene modification with multiple associations.
Modifies scenes for multi-output transmitters without other inputs.
Modifies scenes for multi-output transmitters with wired inputs.
Modifies scenes for master transmitters controlling multiple outputs.
Copies the function and presets from one transmitter to a new one.
Procedure to delete a single transmitter from the selected output.
Deletes all memorized transmitters for a specific output.
Clears the entire memory of all memorized transmitters.
Deletes a specific transmitter using its internal button.
Describes error conditions like memory full or code not found.
Activates/deactivates memory of the last load value after OFF command.
Sets the minimum dimming level for resistive loads.
Modifies settings for automatic load type identification.
Guidelines for safe installation and potential hazards.
Recommendations for product mounting and placement.
Specifications for safe electrical connections and cable ratings.
General safety advice for operating the appliance and potential risks.
Instructions for proper disposal of the product at its end of life.
Details on power supply voltage and operating frequency.
Specifies the maximum power output per channel and total.
Lists the supported radio reception frequencies.
Defines the operational temperature limits.
Indicates the total number of transmitters that can be memorized.
Details terminal connections for high voltage and low voltage inputs/outputs.
Indicates output selection via P4 button or radio transmission.
Configuration options for PIR sensor output selection.
Dip-switch settings for controlling load characteristics.
LEDs indicating overload or overtemperature faults.
Configures load type and functioning mode (switching/dimming).
Sets PIR sensor activation time for all outputs.
Procedure to memorize 7/42 channel transmitters for scenes and dimming.
Memorizes a single button for ON/OFF and Dimming function.
Memorizes a button for ON function, retaining last output level.
Memorizes a button for OFF function, turning the load off.
Memorizes 3-channel transmitters for dimming and ON/OFF.
Memorizes Green Mouse for automatic light control.
Memorizes 4-channel transmitters for preset scene selection.
Memorizes a button for ON-OFF function with short pulses.
Memorizes wireless PIR sensors for automatic load activation.
Procedure to disable or enable transmitter buttons.
Modifies preset scenes for a transmitter associated with a single output.
Identifies outputs for preset scene modification with multiple associations.
Modifies scenes for multi-output transmitters without other inputs.
Modifies scenes for multi-output transmitters with wired inputs.
Modifies scenes for master transmitters controlling multiple outputs.
Copies the function and presets from one transmitter to a new one.
Procedure to delete a single transmitter from the selected output.
Deletes all memorized transmitters for a specific output.
Clears the entire memory of all memorized transmitters.
Deletes a specific transmitter using its internal button.
Describes error conditions like memory full or code not found.
Activates/deactivates memory of the last load value after OFF command.
Sets the minimum dimming level for resistive loads.
Modifies settings for automatic load type identification.
Guidelines for safe installation and potential hazards.
Recommendations for product mounting and placement.
Specifications for safe electrical connections and cable ratings.
General safety advice for operating the appliance and potential risks.
Instructions for proper disposal of the product at its end of life.
Details on power supply voltage and operating frequency.
Specifies the maximum power output per channel and total.
Lists the supported radio reception frequencies.
Defines the operational temperature limits.
Indicates the total number of transmitters that can be memorized.
General
