Tempatron PID500 - Function Menu

Fig4.Output1-Linearcurrent.
Fig5.Output1-Linearvoltage.
4
5
LOAD
0-5V
OR
0-10V
Minimum
Load10K
Ohms
NO
COM
Maximum
Load500
Ohms
4
5
LOAD
4-20mA
NO
COM
12
Installation
PID500 PID110&330
Maximum
Load500
Ohms
11
12
LOAD
4-20mA
NO
COM
PID500 PID110&330
11
12
LOAD
0-5V
OR
0-10V
Minimum
Load10K
Ohms
NO
COM
NOTE:
Foroutput2andoutput3:
1)Configurationissame.
2)Terminalnos-
Output2: 2-3.
Output3: 14-15.
PID500- ;PID110&330-
PID500- ;PID110&330-
13-14
15-16
ONLINEDISPLAY OPTION
Thisfunctionallowsusertoviewonlinedisplayoptions.
NOTE:
Theparametersshownbelowarenotpromptediftheyarelockedinlevel6.
Programming
DISPLAY DESCRIPTION
Setpoint1
Setpoint2
Setpoint3
Proportionalband-heat
Integraltime
Derivativetime
Autotune
Handoutputpercentage
Manualreset
Proportionalband-cool
DISPLAY CONDITION
Rampsetpoint
Online access for Set 2 not
valid if Auxillary output =
Sensor Break / OFF /
Retransmission
Online access for Set 3 not
valid if Alarm mode = Sensor
Break / OFF.
OnlineaccessforAutotune
isnotvalidifPB-Heat=0and
HC=noorPB-Cool=0.
Thisparameterisnot
promptedifPb-H=0
Integraltimeisnot
promptedifPB=0
Derivativetimeisnot
promptedifPB=0
Manualresetisprompted
onlyifIntegral-main=0and
PB-heat>0.
Thisparameterisprompted
onlyifHC=yes.
Thisparameterisprompted
onlyifRampisON/Hold.
Thisparameterisreadonly
andcannotbealtered.
/
31
LockLevel0
LockLevel1
LockLevel2
LockLevel3
LockLevel4
/
/
/
/
/
/
/
/
/
/
Display
Name&Description
Range
Display
condition
Default
value
#IfLOCKselectionisLEVL,thefollowingparameterswillbeprompted.
Changepassword
Newpassword
/
NEW=Id-Y
Programming
Insertjumpertoresetthelock-id.
NOTE:
UNLK-Fullaccesstotheparticularlevel/parameter.
READ-Particularlevel/parametercanbereadbutnotedited.
LOCK-Noaccesstotheparticularlevel/parameter.
30
PR500
P
V
S
V
M
T1
2
3
Lockcode
position
TOCHANGELEVELSPRESS+OR+TOGETHER
Input type
Resolution
Temp unit Display scaling
low
Input scaling
low
Display scaling
high
Input scaling
high
Reverse
scaling
Set2 mode
Set2 type
Set2 value P B - cool Cycle time - cool
Hysteresis
Hysteresis bias
Alarm mode
Alarm mode
Latch alarm
Hold alarm Alarm status Annunciator
Set point 3
Alarm Hysteresis Hysteresis
bias
User ID
Program access
+
+
Online
Set 1 Set 2 Set 3
Auto tune
Appearanceofallshadedmenusdependentonselectionofotherparameters.
Referprogrammingforfutherdetails
*-ApplicableonlyifAlarm2isavailable.
Programming
1. FUNCTIONSMENU
13
On/Off Hysteresis Hysteresis
bias
Tune %age Autotune
Relay 1 mode
O/P power low
limit
O/P power upper
limit
Set mode
Zone number Zone set point Proportional
band
Integral time Derivative time
Heat - cool
Main output
SSR Output Soft start time Hand O/P %
Ramp mode
Ramp rate
Zone
SET=ZONE
Lock level 0
Lock level 1
Lock level 2 Lock level 3 Lock level 4