Tempatron PID500 - Level 1-Output Parameters; Level 3-Alarm 2 Module; Level 4-Special Functions

18
ISC.L =0.00
DSC.L =0.0
RSCL =no
ISC.H=20.00
DSC.H=9999
INPUT
9999
0.0
0.00mA
20.00mA
DISPLAY
Programming
Display
Name&Description
Range
Display
condition
Default
value
Autotune
/
PIDcontrol
4. -OUTPUTPARAMETERSLEVEL 1
Display
Name&Description
Range
Display
condition
Default
value
SetMode
Tunepercentage
/
ZonePID=
YESinlevel4.
Tune=ON
P.AU,75to
100
MainOutputMode
/ Heat-cool=
NO.
Heat-cool mode
The controller can be operated
in heat-cool mode if this
selection is YES.
ZonePID
MainOutput
SSROutput
/
/
( /
)/
/ SSRoutput
model
Display
Name&Description
Range
Display
condition
Default
value
7. -SPECIAL FUNCTIONSLEVEL 4
/
Softstarttime
Handoutputpercentage
Rampmode
Ramprate
Soaktime
Sensoropencondition
Sensorfailpowerlevel
PVbias(DisplayOffset)
, to
minutes.
,O/P
power low
limit to O/P
power high
limit.
/
/
to
degree/hour.
to
minutes
/
to %;
- to %
incaseof
heat-cool
mode.
to
+ for TC
(RTD) &
to
+ for AIN
models
decimal point
as per
selected.
PIDcontrol
PIDcontrol
Rampmode
=ON/HOLD.
Rampmode
=ON/HOLD.
PIDcontrol
Sensoropen
condition=
MANL.
25
Programming
Display
Name&Description
Range
Display
condition
Default
value
6. -ALARM2MODULE(OPTIONAL)LEVEL 3
Alarm2mode
Alarmlatch
/
/ /
/ /
/ .
/
Alarm2
shouldbe
available.
These
parameters
arenot
promptedif
Alarm2
modeisOFF.
HoldAlarm
RelaystatusforAlarm1
AlarmAnnunciator
/
/
/
Set3Value
to
These
parameters
arenot
promptedif
Alarm2
modeis
OFF/brk.
AlarmHysteresis
Hysteresisbias
to
C
C
O
O
for
TC/RTD;
to
foranalog
input.
to
(for
TC/RTD);
to
forAIN
models
decimal
pointasper
selected
O
C
PARAMETEREXPLANATIONS:
ForparameterexplanationsreferLevel2.
24
Programming
Outputpowerlowerlimit
Outputpowerupperlimit
%too/p
powerhigh
limit; %
too/p
power
upperlimit
(inheatcool
mode)
O/ppower
lowlimitto
%
PIDcontrol
19
Programming
ON-OFFcontrolhysteresis
to
ON-OFF
control
*
PIDcontrol
Display
Name&Description
Range
Display
condition
Default
value
Hysteresisbias
Timer
Integraltime
Derivativetime
Derivativeapproachcontrol
TC/RTD:
Analoginput:
to
asper
decimalpoint
selected.
to
O
to
minutes
to
sec.
to
seconds.
to (x
band)
ON-OFF
control
*
Main=Fd
andcontrolis
ON-OFF.*
Proportionalband-heat
to
o
*NOTE:ForoperatinginON-OFFmodemakeProportionalband=0
(-
forheat
-cool
mode)
PIDcontrol
PIDcontrol
PIDcontrol