Need help?Do you have a question about the Tempest Cyclone 55.210L and is the answer not in the manual?
Critical safety guidelines for installation and operation of the enclosure.
Details dimensions, weights, and rigging specifications for enclosures.
Specifications and usage instructions for mounting bolts.
Explanation of the Unistrut Kit for mounting enclosures.
Critical safety requirement for horizontal projector sliding with the Cyclovator 2 Tilt Kit.
Step-by-step instructions for installing the Cyclone Angle Mount Kit.
Covers common issues and their solutions for the ActiveCool system.
Addresses more complex problems and their resolutions for ActiveCool.
General safety and procedures for wiring power to the enclosure.
Outlines electrical standards applicable to different regions.
Details required AC supply voltages and tolerance for variations.
Explanation of single feed power wiring configuration.
Explanation of split feed power wiring configuration.
Description of the Tempest System Manager (TSM) for network monitoring.
Description of the TEMP protocol for enclosure monitoring via Ethernet.
Explains the default network configuration for the 51.D4.15 Ethernet adapter.
Information on additional support resources for the 51.D4.15 adapter.
Details network configuration steps for System Manager installation.
Explains EtherNode network configuration within the GetSet MV software.
Describes the process of running discovery for Tempest enclosures in the system.
Information on checking the DEC4 firmware revision and its importance.
Overview of default factory settings for DEC4 data modes.
Describes the default operating mode for RDM monitoring.
Explains the operating mode for RDM and DMX control.
Details the service mode for RDM and DMX for troubleshooting.
Defines the temperature and humidity control ranges for DEC4.
Explanation of the function of LED indicators on the control interface.
Guide to setting data mode, address, and response curves in the control menu.
Steps to follow when the SAFE MODE message appears on the display.
Procedure for directly updating the System Control Board firmware.
Steps for installing firmware indirectly using an RDM-TRI interface.
Instructions for mounting projectors in a landscape orientation.
Specific mounting instructions for Christie D4K-40 RGB in landscape format.
Procedure for cleaning the projector port glass.
Steps for checking and replacing the enclosure's air filter.
Troubleshooting steps for issues with projector power.
Troubleshooting steps for enclosure overheating problems.
Checks for dirt and debris within the enclosure.
Troubleshooting steps for water ingress into the enclosure.
Diagnosing fan operation issues when the fan LED is illuminated.
Diagnosing heater operation issues when the heater LED is illuminated.
Details the physical layer requirements for the TEMP protocol.
Information on how to download the Developer's Guide.
Critical safety guidelines for installation and operation of the enclosure.
Details dimensions, weights, and rigging specifications for enclosures.
Specifications and usage instructions for mounting bolts.
Explanation of the Unistrut Kit for mounting enclosures.
Critical safety requirement for horizontal projector sliding with the Cyclovator 2 Tilt Kit.
Step-by-step instructions for installing the Cyclone Angle Mount Kit.
Covers common issues and their solutions for the ActiveCool system.
Addresses more complex problems and their resolutions for ActiveCool.
General safety and procedures for wiring power to the enclosure.
Outlines electrical standards applicable to different regions.
Details required AC supply voltages and tolerance for variations.
Explanation of single feed power wiring configuration.
Explanation of split feed power wiring configuration.
Description of the Tempest System Manager (TSM) for network monitoring.
Description of the TEMP protocol for enclosure monitoring via Ethernet.
Explains the default network configuration for the 51.D4.15 Ethernet adapter.
Information on additional support resources for the 51.D4.15 adapter.
Details network configuration steps for System Manager installation.
Explains EtherNode network configuration within the GetSet MV software.
Describes the process of running discovery for Tempest enclosures in the system.
Information on checking the DEC4 firmware revision and its importance.
Overview of default factory settings for DEC4 data modes.
Describes the default operating mode for RDM monitoring.
Explains the operating mode for RDM and DMX control.
Details the service mode for RDM and DMX for troubleshooting.
Defines the temperature and humidity control ranges for DEC4.
Explanation of the function of LED indicators on the control interface.
Guide to setting data mode, address, and response curves in the control menu.
Steps to follow when the SAFE MODE message appears on the display.
Procedure for directly updating the System Control Board firmware.
Steps for installing firmware indirectly using an RDM-TRI interface.
Instructions for mounting projectors in a landscape orientation.
Specific mounting instructions for Christie D4K-40 RGB in landscape format.
Procedure for cleaning the projector port glass.
Steps for checking and replacing the enclosure's air filter.
Troubleshooting steps for issues with projector power.
Troubleshooting steps for enclosure overheating problems.
Checks for dirt and debris within the enclosure.
Troubleshooting steps for water ingress into the enclosure.
Diagnosing fan operation issues when the fan LED is illuminated.
Diagnosing heater operation issues when the heater LED is illuminated.
Details the physical layer requirements for the TEMP protocol.
Information on how to download the Developer's Guide.
To Next Page
General