Tennant 1240 - User Manual

Other manuals for Tennant 1240

Operator's Manual10 pages

Questions and Answers

J
Jennifer JohnsonAug 15, 2025
What to do if my Tennant Floor Machine has poor pick up?
- D
  Denise AveryAug 15, 2025
  If the Tennant Floor Machine isn't picking up properly, there could be several reasons: * The drain hose plug might be loose – make sure it's securely capped. * The float shut-off screen could be clogged; remove the recovery dome and clean off any lint. * There might be air leakage around the recovery dome; tighten the knobs or replace the gaskets. * Vacuum hose connections could be loose; ensure they are secure. * The vacuum hose itself might be defective and need replacement. * Vacuum hose cuffs might be loose; secure them to the hose. * You might be pulling the machine too fast; try slowing down the cleaning process.
Z
zcooperAug 18, 2025
Why is the brush motor not working on my Tennant 1240 Floor Machine?
- P
  Paul NguyenAug 18, 2025
  If your Tennant Floor Machine's brush motor isn't working, a few things could be the cause: 1. The brush motor circuit breaker might have tripped. If so, remove any obstructions from the brush or readjust the brush height, then reset the breaker button at the bottom of the switch box. 2. Make sure the Brush/Spray button is pushed. For other potential issues like a faulty brush motor, loose or broken brush belt, or faulty switch/wiring, contacting a service center may be required.
B
Brian MartinAug 21, 2025
What to do if the vacuum motor does not operate on Tennant Floor Machine?
- J
  James SanchezAug 22, 2025
  If the vacuum motor on your Tennant Floor Machine isn't running, it could be due to a few reasons: * The vacuum motor thermal overload might have tripped. Check for any airflow obstructions and allow 20 minutes for the motor to cool down. * Worn carbon brushes may also be the reason. Replace the brushes or call for service.
J
Joseph RichardAug 25, 2025
Why is my Tennant Floor Machine not picking up water?
- L
  loganwilliamAug 25, 2025
  If your Tennant Floor Machine isn't picking up water well, several factors could be at play. The float shut-off screen might be activated, in which case you should drain the recovery tank. Check for a loose drain hose plug and ensure it's securely capped. A clogged float shut-off screen can also cause this issue; remove the recovery lid and clean the screen. Other potential causes include air leakage around the recovery lid (re-position or replace gaskets), loose vacuum hose connections (secure them), a defective vacuum hose (replace it), loose vacuum hose cuffs (secure them to the hose), damaged, loose, or missing pickup head shoes (repair or replace them), or pulling the machine too fast (slow down the cleaning process).
S
Scott WilsonAug 27, 2025
Why is the vacuum motor not working on my Tennant Floor Machine?
- S
  Stephanie OrtizAug 27, 2025
  If the vacuum motor on your Tennant Floor Machine isn't running, the vacuum motor thermal overload may have tripped. Check the airflow for obstructions and wait 20 minutes for the motor to cool down. Other potential causes, such as loose or broken wiring, a faulty Vacuum/Pump switch, or a defective vacuum motor, require contacting a service center. Also, worn carbon brushes can cause this issue; replace the brushes or call for service.
A
Anthony LarsenAug 30, 2025
How to fix uneven spray on Tennant 1240?
- W
  williamsonsarahAug 31, 2025
  If your Tennant Floor Machine isn't spraying evenly, or not at all, here's what you can check: * The spray tips might be dirty or plugged; try cleaning or replacing them. * The spray tip size or angle might be incorrect; replace them with the proper tips. * The spray tips could be worn; replace them. * The solution tank might be low or empty; refill it. * The solution tank filter might be plugged; clean it.
M
Michael WoodSep 2, 2025
What to do if my Tennant 1240 does not turn on?
- B
  brian64Sep 3, 2025
  If your Tennant Floor Machine isn't turning on, it could be due to a tripped building circuit breaker. Try resetting the breaker. If that doesn't work, the issue might be with faulty switches, wiring, or the power cord. In these cases it is best to contact a service center.
K
Kelly LeeSep 5, 2025
How to fix a Tennant 1240 Floor Machine brush motor that won't start?
- K
  Kiara MedinaSep 5, 2025
  If the brush motor on your Tennant Floor Machine isn't working, start by ensuring the Brush/Spray Triggers are pulled. If that's not the issue, the brush motor circuit breaker may have tripped. Check for any brush obstructions or readjust the brush height, then reset the brush breaker button at the bottom of the switch box. For other potential causes, like a faulty brush motor, loose or broken brush belt, or faulty switch or wiring, it is best to contact a service center.
M
martinezbrettSep 8, 2025
What to do if the solution pump on my Tennant 1240 is not working?
- S
  shahlauraSep 8, 2025
  If the solution pump on your Tennant Floor Machine isn't working, it might be due to an overheated pump. Determine the cause and wait 20 minutes for the pump to cool down. For other potential causes like a faulty solution pump, faulty solenoid, faulty switch, or loose/broken wiring, it is best to contact a service center.
C
Chad WellsSep 12, 2025
How to resolve uneven spray from my Tennant Floor Machine?
- N
  Nichole SmithSep 12, 2025
  If your Tennant Floor Machine has uneven or no spray, first check if the solution tank is low or empty and refill it. Dirty or plugged spray tips and screens can also cause this; clean or replace them. If the spray tip size or angle is improper, replace them with the correct tips. Worn spray tips should also be replaced. Additionally, check for a plugged solution tank filter and clean it, or pinched/kinked internal solution hoses, which should be rerouted or replaced. For a faulty solution pump, it is best to contact a service center.