Tennant E5 - User Manual

Questions and Answers

S
Scott MartinezAug 13, 2025
Why is my Tennant E5 not picking up water?
- J
  John Cordova DDSAug 13, 2025
  If your Tennant Floor Machine isn't picking up water effectively, several factors could be the cause. Start by checking the vacuum hose port cover for looseness. A clogged shut-off float, vacuum intake screen, or vacuum shoe can also lead to poor pickup—clean any debris you find. Inspect the tank cover gaskets for wear and replace if needed. For clogs in the vacuum shoe hose or a faulty vacuum motor, it is recommended to contact Service Center.
R
robertfigueroaAug 17, 2025
Why does my Tennant Floor Machine not operate?
- B
  Brian PageAug 17, 2025
  If your Tennant Floor Machine isn't operating, a faulty power cord could be the reason; consider replacing it. Another possibility is a tripped circuit breaker. If this is the case, unplug the power cord, determine the cause, and reset the 15 amp circuit breaker button. If the circuit breaker continues to trip, it is recommended to contact Service Center.
C
Cheyenne MccoyAug 20, 2025
What to do if the brush does not spin on Tennant E5?
- S
  Suzanne RiggsAug 20, 2025
  If the brush on your Tennant Floor Machine isn't spinning, a tripped circuit breaker might be the cause. Unplug the power cord, check the brush for any obstructions, and then reset the 5 amp circuit breaker button. If the brush belt is broken, or if there's a faulty brush motor or worn carbon brushes, it is recommended to contact Service Center.
J
juliesmithAug 25, 2025
What to do if my Tennant Floor Machine does not operate?
- E
  Erin SavageAug 25, 2025
  If your Tennant Floor Machine isn't operating, it might be due to a faulty power cord, so try replacing it. Another possible cause is a tripped circuit breaker. If this happens, unplug the power cord to determine the cause, then reset the 7.5 amp circuit breaker button. If the circuit breaker continues to trip, further assistance may be needed.
H
hstewartAug 28, 2025
How to improve water pickup on Tennant Floor Machine?
- J
  John FergusonAug 28, 2025
  If your Tennant Floor Machine isn't picking up water effectively, start by checking the vacuum hose port cover on the vacuum shoe to ensure it's not loose. Also, inspect the shut-off float, vacuum intake screen, and vacuum shoe for any clogs and remove any debris. Worn tank cover gaskets can also cause poor water pickup, so consider replacing them.
R
Robert DavenportSep 1, 2025
What to do if the brush does not spin on my Tennant Floor Machine?
- J
  Jay PalmerSep 1, 2025
  If the brush on your Tennant Floor Machine isn't spinning, the circuit breaker may have tripped. Unplug the power cord and inspect the brush for any obstructions, then reset the 2.5 amp circuit breaker button.
D
Danielle HarringtonSep 4, 2025
What to do if Tennant E5 has uneven spray or carpet streaking?
- A
  Amber BarkerSep 5, 2025
  If your Tennant Floor Machine isn't spraying evenly or is causing carpet streaking, there are several potential causes. First, ensure that the cleaning mode switch is properly set. Clogged or faulty spray tips can also be the culprit, so clean or replace them and adjust their angle. Make sure the solution tank isn't empty and that the solution hose screen is free of debris. For damaged solution hoses or a faulty solution pump, it is recommended to contact Service Center.
B
Becky StewartSep 8, 2025
Why is my Tennant Floor Machine leaving streaks?
- J
  Jacqueline AndersonSep 8, 2025
  If you're experiencing uneven spray or carpet streaking with your Tennant Floor Machine, several factors could be at play. Ensure the cleaning mode is properly set. Check for clogged spray tips and clean or replace them if necessary. Make sure the spray tip angle is correct and replace faulty spray tips. Refill the solution tank if it’s empty. Also, inspect the solution hose screen for clogs and remove any debris.

Summary

SAFETY PRECAUTIONS

FOR SAFETY

Lists actions for safe operation and potential hazards to operator or equipment.

GROUNDING INSTRUCTIONS

SAFETY LABELS

MACHINE COMPONENTS OVERVIEW

SWITCH SYMBOLS EXPLAINED

Explains the meaning of various switch symbols used on the machine controls.

MACHINE SETUP PROCEDURES

INSTALLING THE BRUSH

Step-by-step guide for correctly installing the machine's brush.

FILLING THE SOLUTION TANK

Instructions for filling the solution tank with water and detergent.

CONNECTING THE POWER CORD

OPERATING THE CARPET EXTRACTOR

PRE-OPERATION CHECKS

Steps to perform before operating the machine for optimal safety and performance.

CLEANING CARPETS WITH MACHINE

Procedure for cleaning carpets using the machine, including handle adjustment.

USING ACCESSORY TOOLS

MACHINE MAINTENANCE SCHEDULE

MAINTENANCE AFTER EACH USE

Tasks to perform after each use for machine upkeep and longevity.

100-HOUR MAINTENANCE

Maintenance procedures required after every 100 hours of operation.

BRUSH MOTOR MAINTENANCE

Information regarding maintenance and replacement of brush motor carbon brushes.

PROPER MACHINE STORING

RECOMMENDED SPARE PARTS

TROUBLESHOOTING GUIDE

MACHINE SPECIFICATIONS

Tennant E5 Specifications

General

Model	E5
Power Source	Electric
Voltage	120 V
Recovery Tank Capacity	5 gal / 19 L
Power Cord Length	50 feet
Cleaning Path	20 inches
Solution Tank Capacity	5 gallons