Factory Defaults Premier 640 Quick Reference Guide
2 INS296
Factory Defaults
Menu Option Default
Engineer Code
Setup Users User 00 (Engineer) 1234
1. Zone Setup
Zones Types 1 Entry/Exit 1
2 Guard Access
3 - 8 Guard
All Other Zones Not Used
Zone Areas All Zones Area 01
Zone Text All Zones Not Defined
Zone Chime All Zones Silent
Remote Test All Zones Off
2. Area Programming
Timers Exit Delay 030 Seconds
(All Areas) Entry Delay 1 045 Seconds
Entry Delay 2 045 Seconds
2
nd
Entry Dly 000 Seconds
Bell Delay
!
000 Minutes
Bell Duration 015 Minutes
Coms Delay 000 Seconds
Part Bell Dly 000 Seconds
Arming Modes All Areas
!
Entry/Exit
Area Arm Suites All Suites
!
No Areas
Area Suite Text All Suites
!
Not Defined
Suite Arm Modes All Suites
!
Timed
Area Options 1: Auto Part Arm
!
No Areas
2: Part Arm Instant
!
No Areas
3: Part Arm Silent
!
No Areas
4: Remote Arm All Areas
5: Remote Disarm
!
All Areas
6: Panel Tamper
!
Area A
7: Bell Tamper
!
Area A
8: Auxiliary Tamper
!
Area A
9: Panel Speaker
!
All Areas
10: Bell & Strobe op
!
All Areas
11: Alarm Eng Reset
!
No Areas
12: Confirmation Reset
!
All Areas
13: Tamper Eng Reset
!
All Areas **
14: Anti-code Reset
!
All Areas
15: ATS Path Faults
!
Area A
16: Arm With No ATS
!
No Areas **
17: AC Mains Fail
!
Area A
18: Arm With AC Fail Area A
19: Full Arm Coms
!
All Areas
20: Part Arm Coms
!
No Areas
21: Unarm Fire Coms
!
No Areas
22: Unarm Tamp Coms
!
All Areas **
23: Auto Arm Areas
!
No Areas
24: Area A Foyer
!
No Areas
25: Log Part Omits
!
No Areas
26: Multi Knock Area
!
No Areas
27: UDL Keypad
!
All Areas
28: Auto Chime (C2A)
!
No Areas
29: Confirm In Entry
!
No Areas
30: Conf. After Entry
!
All Areas
31: Part Arm Enabled
!
ALL Areas
32: Bell Squawk
!
No Areas
33: Fob After Entry
!
All Areas
34: Armed = Coms
!
No Areas
35: 2 Wire Smoke
!
No Areas
36: Faults Eng Reset
!
All Areas **
37: No ATS Eng Reset
!
All Areas **
38: AC Fail Eng Rst
!
All Areas **
39: Mask When Armed
!
All Areas
Time Arm Areas All Area Profiles
!
Not Defined
Area Text All Areas Not Defined
Menu Option Default
2. Area Programming Continued
Area Profiles Area 00 No Areas
Area 80 All Areas
Area 01 Area A1
Area 02 Area A2
Area 03 Area A3
And so on until
Area 63 Area H7
Area 64 Area H8
Areas 65 – 79 Not defined
3. Global Options
System Timers 1: Exit Settle Time 008 Seconds
2: Global Bell Dly. 000 Minutes
3: Global Bell Dur. 015 Minutes
4: Double Knock Dly 007 Seconds
5: Beam Pair Time 060 Seconds
6: Activity Delay 024 Hours
7: Abort Delay 180 Seconds
8: Courtesy Time 060 Seconds
9: Defer Arming By 030 Minutes
10: Auto Arm Delay 030 Minutes
11: Menu Time Out 180 Seconds
12: Pulse Period 1 010 Seconds
13: Pulse Period 2 020 Seconds
14: Pulse Period 3 030 Minutes
15: ATS Fault Delay 000 Minutes
16: AC Off Delay 005 Minutes
17: Batt Test Period 024 Hours
18: Batt Test Time 010 Seconds
19: Soak Test Time 014 Days
20: Service Interval 000 Weeks
21: Test Call Every 024 Hours **
22: Min Random Time 000 Seconds
23: Max Random Time 060 Seconds
24: Door Strike Time 005 Seconds
25: Zone Response 008 x 8mSec.
26: Keypad PA Delay 060 Seconds
27: Confirmation Dly 060 Minutes
28: Warning Delay 000 Minutes
29: Keypad Lock time 090 Seconds
30: Eng. Log Off Dly 060 Minutes
31: Fire Bell Delay 000 Minutes
32: Forced Entry Dly 005 Seconds
33: Supervision Time 030 Minutes
34: Poll IP Every 000 Minutes
System Config. 00: Bell on Arm Fail No Bell
01: Bell is an SCB SAB
02: Clock is 12Hr 24Hr
03: Manual BST/GMT Auto
04: Hide Armed Areas View
05: Area Bell Time Global
06: 24Hr Omit Local Global
07: Leave Omits Remove
08: Enforce Com Delay Override
09: NVM is Locked Unlocked
10: Engineer Only User + Engineer
11: Chime Visible Audible
12: Omit Tampers NO YES **
13: Offline Printing Online
14: View Act. Fault Hide
15: Hide Exit Errors Hide
16: No Code Tamp Enable
17: Code Tamp Alarms Locks **
18: Areas 1-8 & I-P A-H & I-P
19: Man. Area Select Auto
20: Normal Text Predictive
21: Zone Short = Active Tamper
22: R/R=Silence/RST Reset Only
To Next Page
Loading...
Need help?
General
