Thermal Dynamics 1Torch SL100 Hand Torch User Manual

Manual 0-2962 A-9 APPENDIX
Cutting Speed Charts
NOTES
* Gas pressure shown is for torches with leads up to 25' / 7.6 m long. For 50' / 15.2 m leads, set gas
pressure to 80 psi / 5.5 bar.
5PUBMnPXSBUFJODMVEFTQMBTNBBOETFDPOEBSZHBTnPX
Air Plasma Cutting Speed Data Chart For CutMaster 75 & CutMaster 81
munimulA :lairetaM epyT06LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
ThicknessTip Output VoltsAmperage Speed (Per Minute)StandoffPlasma Gas Press Flow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC) (Amps) Inches Meters Inches mm psi* barPlasmaTotal** Delay (Sec) Inches mm
0.06 1.69-8210 95 60 3508.890.194.8 70 4.880400 00.1
94
.8
0.125 3.29-8210 98 60 1754.450.194.8 70 4.880 400 00.1
94
.8
1/46.4 9-8210 10260802.030.1 94.8 70 4.880400 00.1
94
.8
3/89.5 9-8210 10960441.120.1 94.8 70 4.880400 00.1
94
.8
1/2 12.79-8210 11560230.580.1 94.8 70 4.880400 00.1
94
.8
3/4 19.19-8210 11760110.280.1 94.8 70 4.880 400 NR 0.19 4.8
Air Plasma Cutting Speed Data Chart For CutMaster 75 & CutMaster 81
leetS dliM :lairetaM epyT06LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
ThicknessTip Output VoltsAmp erageSpeed (Per Minute) Standoff Plasma Gas PressFlow (SCFH) PiercePierce Height
Inches
mm
(Cat. No.) (VDC)(Amps)InchesMetersInchesmmpsi*bar Plasma Total**Delay (Sec)Inchesmm
0.06 1.69-8210 95 60 3508.890.194.8 70 4.880 400 00.1
94
.8
1/83.2 9-8210 98 60 1754.450.194.8 70 4.880 400 00.1
94
.8
1/46.4 9-8210 102 60 80 2.03 0.19 4.8704.8 80 40000.19 4.8
3/89.5 9-8210 109 60 44 1.12 0.19 4.8704.8 80 40000.19 4.8
1/2 12.79-8210 115 60 23 0.58 0.19 4.8704.8 80 40000.19 4.8
3/4 19.19-8210 117 60 11 0.28 0.19 4.8704.8 80 400NR0.1
94
.8
Air Plasma Cutting Speed Data Chart For CutMaster 75 & CutMaster 81
leetS sselniatS :lairetaM epyT06LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
ThicknessTip Output VoltsAmperage Speed (Per Minute)StandoffPlasma Gas Press Flow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC) (Amps) Inches Meters Inches mm psi* barPlasmaTotal** Delay (Sec) Inches mm
0.06 1.69-8210 95 60 3508.890.194.8 70 4.880400 00.1
94
.8
1/83.2 9-8210 98 60 1503.810.194.8 70 4.880400 00.1
94
.8
1/46.4 9-8210 10260701.780.1 94.8 70 4.880400 00.1
94
.8
3/89.5 9-8210 10960350.890.1 94.8 70 4.880400 00.1
94
.8
1/2 12.79-8210 11560200.510.1 94.8 70 4.880400 00.1
94
.8
3/4 19.19-8210 11760100.250.1 94.8 70 4.880 400 NR 0.19 4.8

Thermal Dynamics 1Torch SL100 Hand Torch Specifications

General

Brand	Thermal Dynamics
Model	1Torch SL100 Hand Torch
Category	Welding Accessories
Language	English