Thermal Dynamics 1Torch SL100 Hand Torch User Manual

Manual 0-2962 1-1 GENERAL INFORMATION
SECTION 1:
GENERAL INFORMATION
1.01 Notes, Cautions and Warnings
Throughout this manual, notes, cautions, and warnings are
used to highlight important information. These highlights
are categorized as follows:
NOTE
An operation, procedure, or background infor
-
mation which requires additional emphasis or
is helpful in efficient operation of the system.
CAUTION
A procedure which, if not properly followed,
may cause damage to the equipment.
WARNING
A procedure which, if not properly followed,
may cause injury to the operator or others in
the operating area.
1.02 Important Safety Precautions
WARNINGS
OPERATION AND MAINTENANCE OF PLASMA
ARC EQUIPMENT CAN BE DANGEROUS AND
HAZARDOUS TO YOUR HEALTH.
Plasma arc cutting produces intense electric
and magnetic emissions that may interfere
with the proper function of cardiac pacemak
-
ers, hearing aids, or other electronic health
equipment. Persons who work near plasma arc
cutting applications should consult their medi-
cal health professional and the manufacturer of
the health equipment to determine whether a
hazard exists.
To prevent possible injury, read, understand
and follow all warnings, safety precautions and
instructions before using the equipment. Call
1-603-298-5711 or your local distributor if you
have any questions.
GASES AND FUMES
Gases and fumes produced during the plasma cutting
process can be dangerous and hazardous to your health.
t ,FFQBMMGVNFTBOEHBTFTGSPNUIFCSFBUIJOHBSFB
Keep your head out of the welding fume plume.
t 6TF BO BJSTVQQMJFE SFTQJSBUPS JGWFOUJMBUJPO JT OPU
adequate to remove all fumes and gases.
t 5IFLJOETPGGVNFTBOEHBTFTGSPNUIFQMBTNBBSD
depend on the kind of metal being used, coatings
on the metal, and the different processes. You must
be very careful when cutting or welding any metals
which may contain one or more of the following:
Antimony Chromium Mercury
Arsenic Cobalt Nickel
Barium Copper Selenium
Beryllium Lead Silver
Cadmium Manganese Vanadium
t "MXBZTSFBEUIF.BUFSJBM4BGFUZ%BUB4IFFUT.4%4
that should be supplied with the material you are
using. These MSDSs will give you the information
regarding the kind and amount of fumes and gases
that may be dangerous to your health.
t 'PSJOGPSNBUJPOPOIPXUPUFTUGPSGVNFTBOEHBTFT
in your workplace, refer to item 1 in Subsection 1.03,
Publications in this manual.
t 6TFTQFDJBMFRVJQNFOUTVDIBTXBUFSPSEPXOESBGU
cutting tables, to capture fumes and gases.
t %POPUVTFUIFQMBTNBUPSDIJOBOBSFBXIFSFDPN-
bustible or explosive gases or materials are located.
t 1IPTHFOFBUPYJDHBTJTHFOFSBUFEGSPNUIFWBQPST
of chlorinated solvents and cleansers. Remove all
sources of these vapors.
t 5IJT QSPEVDU XIFO VTFE GPSXFMEJOH PS DVUUJOH
produces fumes or gases which contain chemicals
known to the State of California to cause birth defects
and, in some cases, cancer. (California Health &
Safety Code Sec. 25249.5 et seq.)
ELECTRIC SHOCK
Electric Shock can injure or kill. The plasma arc process
uses and produces high voltage electrical energy. This
electric energy can cause severe or fatal shock to the
operator or others in the workplace.

Thermal Dynamics 1Torch SL100 Hand Torch Specifications

General

Brand	Thermal Dynamics
Model	1Torch SL100 Hand Torch
Category	Welding Accessories
Language	English