Thermal Dynamics 1Torch SL100 Hand Torch User Manual

Manual 0-2962 A-23 APPENDIX
Cutting Speed Charts
NOTES
* Gas pressure shown is for torches with leads up to 25' / 7.6 m long. For 50' / 15.2 m leads, set gas
pressure to 65 psi / 4.5 bar.
5PUBMnPXSBUFJODMVEFTQMBTNBBOETFDPOEBSZHBTnPX
Air Plasma Cutting Speed Data Chart For PakMaster 75XL Plus
munimulA :lairetaM epyT001LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
Thickness TipOutput VoltsAmperageSpeed (Per Minute) StandoffPlasma Gas PressFlow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC)(Amps)InchesMetersInchesmmpsi*bar Plasma Total** Delay (Sec)Inchesmm
1/16 1.69-8210 95 60 3508.890.194.8 60 4.180350 0.10.2
56
.4
1/8 3.29-8210 95 60 1754.450.194.8 60 4.180350 0.25 0.25 6.4
1/4 6.49-8210 10560802.030.194.8 60 4.180350 0.25 0.25 6.4
3/8 9.59-8210 10560451.140.194.8 60 4.180350 0.25 0.25 6.4
1/2 12.7 9-8210 10560220.560.194.8 60 4.180350 0.50.256.4
3/4 19.1 9-8210 11560120.300.194.8 60 4.180350 NA NA NA
Air Plasma Cutting Speed Data Chart For PakMaster 75XL Plus
leetS dliM :lairetaM epyT001LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
Thickness TipOutput VoltsAmp erageSpeed (Per Minute)StandoffPlasma Gas PressFlow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC)(Amps)InchesMetersInchesmmpsi*bar Plasma Total** Delay (Sec)Inchesmm
1/16 1.69-82109060350 8.89 0.19 4.8604.1 80 3500.1 0.25 6.4
1/8 3.29-82109560175 4.45 0.19 4.8604.1 80 3500.250.256.4
1/4 6.49-8210105 60 80 2.03 0.19 4.8604.1 80 3500.250.256.4
3/8 9.59-8210105 60 45 1.14 0.19 4.8604.1 80 3500.250.256.4
1/2 12.7 9-8210 10560220.560.194.8 60 4.180350 0.50.256.4
3/4 19.1 9-8210 11560110.280.194.8 60 4.180350 NA NA NA
125.49-8210115 60 80.200.194.8 60 4.180350 NA NA NA
Air Plasma Cutting Speed Data Chart For PakMaster 75XL Plus
leetS sselniatS :lairetaM epyT001LS :hcroT epyT
hcroT saG elgniS :saG yradnoceS epyTriA :saG amsalP epyT
ThicknessTip Output VoltsAmperageSpeed (Per Minute) StandoffPlasma Gas Press Flow (SCFH) Pierce Pierce Height
Inches
mm
(Cat. No.) (VDC) (Amps) Inches Meters Inches mm psi* barPlasmaTotal** Delay (Sec) Inches mm
1/16 1.69-8210 95 60 350 8.89 0.19 4.8604.1 80 3500.1 0.25 6.4
1/8 3.29-82109560 150 3.81 0.19 4.8604.1 80 3500.250.2
56
.4
1/4 6.49-8210105 60 70 1.78 0.19 4.8604.1 80 3500.250.2
56
.4
3/8 9.59-8210105 60 35 0.89 0.19 4.8604.1 80 3500.250.2
56
.4
1/2 12.7 9-8210105 60 20 0.51 0.19 4.8604.1 80 3500.5 0.25 6.4
3/4 19.1 9-8210 11560100.250.194.8 60 4.180350 NA NA NA

Thermal Dynamics 1Torch SL100 Hand Torch Specifications

General

Brand	Thermal Dynamics
Model	1Torch SL100 Hand Torch
Category	Welding Accessories
Language	English