Why the Touchscreen Console will not control the TCU on ThermoFisher Scientific thermo scientific imPULSE S.U.M.?
If the Touchscreen Console will not control the TCU, it might be due to: * Issue with TCU parameters. * Issue with TCU cordsets.
Why temperature readings are not displaying on ThermoFisher Scientific Laboratory Equipment?
If temperature readings are not displaying or the system fails to recognize a sensor, it could be due to: * Issue with RTD. * Issue with cordset.
Why BPC Pressure module is not pumping air into the BPC on ThermoFisher Scientific Laboratory Equipment?
If the BPC Pressure module/PCD Pressure Module isn't pumping air into the BPC when Start/Inflate is touched, it could be due to: * An issue with the air supply into the Touchscreen Console. * An issue with pneumatic solenoid valves.
Why Touchscreen Console has multiple breaker trips on ThermoFisher Scientific thermo scientific imPULSE S.U.M. Laboratory Equipment?
Multiple breaker trips within 4 hours on the Touchscreen Console may indicate: * Inadequate power supply; ensure that no other device is sharing the power outlet. * Too much power consumed by devices (defective or otherwise) connected on auxiliary power outlets; remove device(s) to identify defective component.
What to do if the motor drive of my ThermoFisher Scientific Laboratory Equipment will not run?
If the motor drive isn't running, try these steps: * Check the guard and guard sensor to ensure they are fully in place. Adjust the guard until it is in the correct position, and/or adjust the guard sensor as necessary. * On larger units, check that the door is closed and that the emergency reset button has been pressed. * Check the circuit breaker to see if it has been tripped. If it was, reset the circuit breaker. * Ensure that the crank shaft is unbroken, and the linear bearings are not jammed. Replace them if necessary.
What to do if BPC pressure is not reading on ThermoFisher Scientific thermo scientific imPULSE S.U.M.?
If the BPC pressure is not reading, it might be due to: * A pressure sensor in BPC not working. * A connection issue between the pressure sensor and the Touchscreen Console.
Why conductivity readings are not displaying on ThermoFisher Scientific thermo scientific imPULSE S.U.M. Laboratory Equipment?
If conductivity readings are not displaying, it could be due to: * Conductivity sensor issue. * Conductivity connection issue.
Why BPC pressure readings are inaccurate on ThermoFisher Scientific Laboratory Equipment?
Inaccurate BPC pressure readings could be due to: * Pressure sensor calibration issue. * Connection issue between pressure sensor and the Touchscreen Console. * PCD connection issue.
Why pH readings are not displaying on ThermoFisher Scientific thermo scientific imPULSE S.U.M.?
If pH readings are not displaying or the pH transmitter is unable to recognize the sensor, it may be due to: * pH connection issue. * pH board issue in the Touchscreen Console.
Why the conductivity readings are inaccurate on ThermoFisher Scientific Laboratory Equipment?
If conductivity readings are inaccurate, consider: * Conductivity calibration issue. * Conductivity sensor issue.
General| Brand | ThermoFisher Scientific |
|---|---|
| Model | thermo scientific imPULSE S.U.M. |
| Category | Laboratory Equipment |
| Language | English |
Provides a general overview of the imPULSE S.U.M. system and its key features.
Details the features and components of the imPULSE mixer's motor drive assembly.
Describes the characteristics and hardware components of the Touchscreen Console.
Covers essential steps for preparing the installation site, including electrical connections.
Provides detailed instructions for the physical installation and setup of the imPULSE S.U.M.
Guide to customizing the Home screen by adding and configuring modules.
Details the process of setting up and using an Administrator profile for enhanced control.
Explains the function and requirements of each available module on the Touchscreen Console.
Step-by-step guide for calibrating the system's pumps for accurate fluid delivery.
Instructions for calibrating the pH sensor to ensure accurate pH measurements.
Procedure for calibrating the conductivity sensor for accurate readings.
Detailed steps and guidelines for filling the imPULSE S.U.M. with liquid.
Instructions on how to start and control the agitation process for effective mixing.
Overview of how to monitor and control various system functions during operation.
To Next Page