Tiger JPC-W10W User Manual

25
24
English
8
3·6
2
7
5
4
Soak timer function
You can set the time for rice to be soaked
naturally before cooking.
• Set the inner pot in the rice cooker, select
“Soak Timer”, and set the time. Cooking starts
automatically when the set time has elapsed.
• The soaking time can be set in increments of 10
minutes from 10 to 60 minutes.
Note
● Example setting: If “Soak Timer” is set to 50
minutes, cooking starts after 50 minutes.
1
Connect the power cord.
(1) Insert the
plug.
(2) Insert the
plug.
Appliance plug
Power plug
2
Press the [Menu • 菜单 /◀▶ ]
key to select the desired menu
P.1 8 .
• It is not necessary to press the [Menu •


/
◀▶
] key if the desired menu is already
selected.
On
2 short
beeps
Check
that the
Keep Warm lamp is o󰀨.
3
When you select the “Porridge”
menu, use the [Hr • 时] and [M • 分]
keys to set the desired cooking
time.
• Pressing the [Hr •

] key increases the time
by 5 minutes while the [M •

] key decreases
it by 5 minutes.
• The cooking time can be set between 40 and
90 minutes in increments of 5 minutes.
Increases by 5 min. Decreases by 5 min.
• The default setting is 60 minutes. Adjust the
time as desired.
4
Select the Keep Warm setting
for after cookingP. 1 8 .
• You do not need to select the Keep Warm
setting if the desired setting has been selected.
5
Press the [Timer • 预约] key and
then select “Soak Timer”.
The selected setting switches between “Timer
1”, “Timer 2”, and “Soak Timer”
each time the
[Timer •
󰂈󰂠
] key is pressed.
• For “Timer 1” and “Timer 2”, see P.22.
On
Blinks
Blinks
Short
beep
Note
● The Soak Timer function is not available in the
following cases.
• When the “Quick”, “Express Limited cups”,
“Sweet”, “Mixed”, “Slow Cook”, “Cake”, or “Clean
care” menu is selected
• When “0:00” is blinking on the display
• When the inner pot is not set
Setting the Soak Timer Function
● If the Keep Warm lamp is on, press the [Cancel •

] key to turn o󰀨 the lamp. (The Soak Timer
function is not available while the Keep Warm
lamp is lit.)

Sounds emitted by the rice cooker
● If you do not operate the rice cooker within
approximately 30 seconds after pressing the
[Timer •
󰂈󰂠
] key, the rice cooker beeps 2 times
(short beeps).
● If the [Timer •
󰂈󰂠
] key is pressed while the rice
cooker is in a state where the Soak Timer function
is not available, the rice cooker beeps 2 times
(short beeps).
● If the sound becomes bothersome, the volume
can be adjusted. (See P.49)
6
Press the [Hr • 时] and [M • 分 ]
keys to set the soaking time.
On
Blinks
Blinks
Short
beep
• The soaking time can be set in increments of
10 minutes from 10 to 60 minutes.
• Pressing the [Hr •

] key increases the
time by 10 minutes while the [M •

] key
decreases it by 10 minutes.

Texture
● Soaking rice for a long time creates a soft texture
when cooked.
7
Press the [Start• 煮饭] key once.
The Soak Timer function is set.
For “Plain” menu
For other menus
On
On
O󰀨
Long
beep
Short and
long beep
On
• If you make a mistake or otherwise want to
reset the timer, press the [Cancel •

] key and
repeat the procedure from step
2
on P.24.

Tiger JPC-W10W Specifications

General

Brand	Tiger
Model	JPC-W10W
Category	Rice Cooker
Language	English