Why does my Toro 41198 Multi-Pro 1250 Paint Sprayer monitor display 6553.5 in the Application Rate setting?
If your Toro Paint Sprayer monitor displays 6553.5 when in the Application Rate setting, contact your Authorized Service Dealer because the monitor is not receiving data from the speed sensor.
Why is a boom section not spraying on my Toro 41198 Multi-Pro 1250?
If a boom section isn't spraying on your Toro Paint Sprayer, consider these possibilities: * The electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, then reconnect it. * A fuse might be blown; check the fuses and replace them as necessary. * A hose might be pinched; repair or replace the hose. * A boom by-pass valve might be improperly adjusted; adjust the boom by-pass valves. * If the boom valve or electrical system is damaged, contact your Authorized Service Dealer.
Why doesn't my Toro Paint Sprayer monitor display application rate or total volume?
If your Toro Paint Sprayer monitor isn't displaying the application rate or total volume, check the following: * Ensure the monitor cable is securely connected. * The flow meter might be dirty or clogged; clean the flow meter. * The flow meter might not be calibrated correctly; calibrate the flow meter. * If the flow meter is damaged, contact your Authorized Service Dealer.
Why Toro 41198 Multi-Pro 1250 starter does not crank?
The starter of your Toro Paint Sprayer might not be cranking due to several reasons: * The range selector might not be in Neutral—press the brake pedal and move the range selector to the Neutral position. * The electrical connections could be corroded or loose—check the electrical connections. * A fuse might be blown or loose—correct or replace the fuse. * The battery could be discharged—charge or replace the battery. * The safety interlock system might be malfunctioning—contact your Authorized Service Dealer. * There might be a broken starter or starter solenoid—contact your Authorized Service Dealer. * The internal engine components could be seized—contact your Authorized Service Dealer.
What to do if Toro 41198 Multi-Pro 1250 engine cranks but will not start?
If your Toro Paint Sprayer's engine cranks but doesn't start, here's what you can check: * Ensure the fuel tank isn't empty by filling it with fresh fuel. * The fuel system might have dirt, water, or stale fuel. In this case, drain and flush the fuel system and add fresh fuel. * A clogged fuel line could be the issue, so clean or replace it. * Make sure the spark plug lead is connected. * Replace the spark plug if it's damaged or dirty. * If the kill relay is not energized or the ignition is broken, contact your Authorized Service Dealer.
Why does my Toro 41198 Multi-Pro 1250 engine start but not keep running?
If your Toro Paint Sprayer engine starts but doesn't keep running, consider the following: * The fuel tank vent might be restricted; replace the fuel cap. * There might be dirt or water in the fuel system; drain and flush the fuel system and add fresh fuel. * The fuel filter could be clogged; replace the fuel filter. * A fuse might be blown or loose; correct or replace the fuse. * For a broken fuel pump, carburetor, or cylinder head gasket; contact your Authorized Service Dealer. * Check and tighten wire connections if they are loose or have poor connections.
Why is my Toro 41198 Multi-Pro 1250 Paint Sprayer engine losing power?
Your Toro Paint Sprayer engine might be losing power due to: * Incorrect crankcase oil level. Adjust it to the full mark. * A dirty air cleaner element. Clean or replace it. * Dirt, water, or stale fuel in the fuel system. Drain and flush the system, then add fresh fuel. * Engine overheating. Refer to the 'Engine Overheats' section. * A damaged or dirty spark plug. Replace it. * A plugged vent hole in the fuel tank vent fitting. Replace the fuel cap. * Low compression. Contact your Authorized Service Dealer.
What does “OFL” mean on my Toro 41198 Multi-Pro 1250 Paint Sprayer monitor?
If the monitor reads “OFL” on your Toro Paint Sprayer, it means the data has exceeded the maximum allowed. Press and hold the [Reset] button to clear the monitor.
What to do if Toro 41198 Multi-Pro 1250 boom section does not turn off?
If a boom section does not turn off on your Toro Paint Sprayer, stop the spray system and pump and turn off the sprayer. Remove the retainer from under the boom valve and pull out the motor and stem. Inspect all parts and replace any that appear damaged.
What causes abnormal vibration or noise in my Toro 41198 Multi-Pro 1250?
Abnormal vibration or noise in your Toro Paint Sprayer could be due to: * Loose engine mounting bolts. Tighten the engine mounting bolts. * A problem with the engine. Contact your Authorized Service Dealer.
Details safe operational procedures and warnings for the sprayer.
Details the various controls and their functions on the sprayer.
Procedures for filling tanks, operating booms, and spraying.
Lists recommended maintenance tasks by service interval.
Diagnosing and resolving common engine and vehicle issues.
Diagnosing and fixing problems with the spray system.
General| Brand | Toro |
|---|---|
| Model | 41198 Multi-Pro 1250 |
| Category | Paint Sprayer |
| Language | English |
To Next Page
