Toro Multi Pro 1250 - User Manual

Questions and Answers

R
Rose EdwardsAug 31, 2025
What should I do if a boom section on my Toro Sprayer does not spray?
- M
  Mary LeeAug 31, 2025
  If a boom section on your Toro Sprayer does not spray, the electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. A pinched hose can also cause this issue, so repair or replace the hose. Make sure that a boom by-pass valve is properly adjusted.
R
Robert EstradaAug 25, 2025
What to do if Toro Paint Sprayer distance is inaccurate?
- W
  wilsonwilliamAug 25, 2025
  If the distance measurement on your Toro Paint Sprayer is inaccurate, calibrate the speed sensor.
J
Jorge WilliamsSep 23, 2025
Why does the monitor display 6553.5 in the Application Rate setting on my Toro Multi Pro 1250 Paint Sprayer?
- T
  Teresa BlackburnSep 23, 2025
  If the monitor displays 6553.5 when in the Application Rate setting on your Toro Paint Sprayer, contact your Authorized Service Dealer, because the monitor is not receiving data from the speed sensor.
B
Brandy PittsSep 4, 2025
What to do if Toro Multi Pro 1250 engine cranks, but will not start?
- S
  sjohnsonSep 4, 2025
  If your Toro Paint Sprayer engine cranks but doesn't start, the fuel tank may be empty, so fill it with fresh fuel. Also, dirt, water, or stale fuel could be in the fuel system, requiring you to drain and flush the fuel system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected, and replace the spark plug if it's damaged or dirty.
T
timothyschneiderSep 9, 2025
What to do if Toro Multi Pro 1250 Paint Sprayer displayed measurements do not make sense?
- T
  Todd FletcherSep 9, 2025
  If the displayed measurements on your Toro Paint Sprayer do not make sense, check the Units of Measurement to ensure that it is set correctly because the Units of Measurement is set to a system other than what you expect.
S
Sandra WoodsSep 2, 2025
Why is the speed always 0 or erratic on my Toro Sprayer?
- V
  Virginia ChambersSep 2, 2025
  If the speed is always 0 or erratic on your Toro Sprayer, connect the monitor cable. Also, calibrate the speed sensor.
S
Stephen RobertsAug 29, 2025
What to do if my Toro Sprayer engine cranks but won't start?
- G
  griffinrachelAug 29, 2025
  If your Toro Sprayer's engine cranks but doesn't start, the fuel tank might be empty; refill it with fresh fuel. Also, the fuel system might contain dirt, water, or stale fuel, requiring you to drain and flush the system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected and replace any damaged or dirty spark plugs.
C
Christopher TorresSep 12, 2025
Why will my Toro Multi Pro 1250 Paint Sprayer engine not idle?
- A
  anthonyshortSep 12, 2025
  If your Toro Paint Sprayer engine will not idle, here are a few potential causes: * The fuel tank vent may be restricted; replace the fuel cap. * There may be dirt, water, or stale fuel in the fuel system; drain and flush the fuel system and add fresh fuel. * A spark plug may be damaged or broken; replace the spark plug. * If the carburetor idle passages are plugged, the idle speed adjusting screw is incorrectly set, the fuel pump is broken, there is low compression, contact your Authorized Service Dealer. * The air cleaner element may be dirty; clean or replace it.
D
Dawn BookerSep 6, 2025
Why does my Toro Multi Pro 1250 Paint Sprayer abnormal vibration or noise?
- W
  Wesley PhamSep 6, 2025
  If you notice abnormal vibration or noise in your Toro Paint Sprayer, tighten the engine mounting bolts if they are loose.
T
Thomas Wagner MDAug 27, 2025
Why is the distance reading inaccurate on my Toro Multi Pro 1250 Paint Sprayer?
- S
  Stephen JacksonAug 27, 2025
  If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.