Toro Multi Pro 1250 - User Manual

Questions and Answers

S
Sarah HaleySep 10, 2025
Why does my Toro Multi Pro 1250 Paint Sprayer engine start but not keep running?
- E
  Elizabeth GarciaSep 10, 2025
  If your Toro Paint Sprayer engine starts but doesn't keep running, consider the following: * The fuel tank vent might be restricted; replace the fuel cap. * There might be dirt or water in the fuel system; drain and flush the fuel system and add fresh fuel. * The fuel filter could be clogged; replace the fuel filter. * A fuse might be blown or loose; correct or replace the fuse. * For a broken fuel pump, carburetor, or cylinder head gasket; contact your Authorized Service Dealer. * Check and tighten wire connections if they are loose or have poor connections.
J
John BergerSep 10, 2025
Why is my Toro Multi Pro 1250 engine losing power?
- V
  valeriefrazierSep 10, 2025
  Your Toro Paint Sprayer engine might be losing power due to: * Incorrect crankcase oil level. Adjust it to the full mark. * A dirty air cleaner element. Clean or replace it. * Dirt, water, or stale fuel in the fuel system. Drain and flush the system, then add fresh fuel. * Engine overheating. Refer to the 'Engine Overheats' section. * A damaged or dirty spark plug. Replace it. * A plugged vent hole in the fuel tank vent fitting. Replace the fuel cap. * Low compression. Contact your Authorized Service Dealer.
S
Sarah JenkinsSep 10, 2025
What causes a Toro Paint Sprayer engine to run but knock or miss?
- B
  Blake TuckerSep 12, 2025
  If your Toro Paint Sprayer engine runs, but knocks or misses, it could be due to: * Dirt, water, or stale fuel in the fuel system. Drain and flush the fuel system; add fresh fuel. * A loose spark plug lead. Reconnect the spark plug lead. * A broken spark plug. Replace the spark plug. * Loose wires or poor connections. Check and tighten wire connections. * Engine overheating. See the Engine Overheats section for guidance.
A
Anthony GarciaSep 12, 2025
Why is a boom section not spraying on my Toro Paint Sprayer?
- Y
  ypopeSep 12, 2025
  If a boom section isn't spraying on your Toro Paint Sprayer, consider these possibilities: * The electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, then reconnect it. * A fuse might be blown; check the fuses and replace them as necessary. * A hose might be pinched; repair or replace the hose. * A boom by-pass valve might be improperly adjusted; adjust the boom by-pass valves. * If the boom valve or electrical system is damaged, contact your Authorized Service Dealer.
S
Shane BensonSep 12, 2025
How to prevent Toro Multi Pro 1250 engine from overheating?
- W
  wrightmichaelSep 12, 2025
  To prevent your Toro Paint Sprayer engine from overheating: * Ensure the crankcase oil level is correct by filling or draining to the full mark. * Reduce excessive loading by using a lower ground speed. * Clean the air intake screens with every use. * Clean the cooling fins and air passages under the engine blower housing and/or the rotating air intake screen with every use. * If the fuel mixture is lean, contact your Authorized Service Dealer.
C
Christopher TorresSep 12, 2025
Why will my Toro Multi Pro 1250 Paint Sprayer engine not idle?
- A
  anthonyshortSep 12, 2025
  If your Toro Paint Sprayer engine will not idle, here are a few potential causes: * The fuel tank vent may be restricted; replace the fuel cap. * There may be dirt, water, or stale fuel in the fuel system; drain and flush the fuel system and add fresh fuel. * A spark plug may be damaged or broken; replace the spark plug. * If the carburetor idle passages are plugged, the idle speed adjusting screw is incorrectly set, the fuel pump is broken, there is low compression, contact your Authorized Service Dealer. * The air cleaner element may be dirty; clean or replace it.
C
carneymelissaSep 12, 2025
Why is the speed reading always 0 or erratic on my Toro Multi Pro 1250 Paint Sprayer?
- E
  eduardocainSep 12, 2025
  If the speed reading on your Toro Paint Sprayer is always 0 or erratic, it could be due to: * A loose monitor cable. Connect the monitor cable. * The speed sensor is not calibrated correctly. Calibrate the speed sensor. * The speed sensor is damaged. Contact your Authorized Service Dealer.
A
Ashley WareSep 12, 2025
What causes a pressure drop when turning on a boom on my Toro Multi Pro 1250?
- D
  Devin WilliamsSep 12, 2025
  A pressure drop when you turn on a boom on your Toro Paint Sprayer may occur because: * The boom bypass valve is improperly adjusted. Adjust the boom bypass valve. * There is an obstruction in the boom valve body. Remove the inlet and outlet connections to the boom valve and remove any obstructions. * A nozzle filter is damaged or clogged. Remove and inspect all nozzles.
S
Stephen LittleSep 12, 2025
Why is my Toro Multi Pro 1250 monitor not functioning?
- N
  Nancy DavisSep 12, 2025
  If your Toro Paint Sprayer monitor isn't functioning, check if: * The monitor cable is loose or disconnected; connect the monitor cable. * If the monitor or cable is damaged, contact your Authorized Service Dealer.
M
Michelle HallSep 12, 2025
Why doesn't my Toro Multi Pro 1250 Paint Sprayer monitor display application rate or total volume?
- M
  michellemoonSep 12, 2025
  If your Toro Paint Sprayer monitor isn't displaying the application rate or total volume, check the following: * Ensure the monitor cable is securely connected. * The flow meter might be dirty or clogged; clean the flow meter. * The flow meter might not be calibrated correctly; calibrate the flow meter. * If the flow meter is damaged, contact your Authorized Service Dealer.