Toro Multi Pro 1250 - User Manual

Questions and Answers

G
gonzalezdanielSep 18, 2025
Why don't the displayed measurements on my Toro Paint Sprayer make sense?
- A
  April WrightSep 18, 2025
  If the displayed measurements do not make sense on your Toro Paint Sprayer, check the Units of Measurement to ensure that it is set correctly.
R
Rose EdwardsAug 31, 2025
What should I do if a boom section on my Toro Sprayer does not spray?
- M
  Mary LeeAug 31, 2025
  If a boom section on your Toro Sprayer does not spray, the electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. A pinched hose can also cause this issue, so repair or replace the hose. Make sure that a boom by-pass valve is properly adjusted.
T
Thomas Wagner MDAug 27, 2025
Why is the distance reading inaccurate on my Toro Multi Pro 1250 Paint Sprayer?
- S
  Stephen JacksonAug 27, 2025
  If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.
R
rebeccasmithSep 23, 2025
Why does the monitor not function on my Toro Multi Pro 1250?
- R
  Ronald BlackburnSep 23, 2025
  If the monitor on your Toro Paint Sprayer does not function, connect the monitor cable if it is loose or disconnected. Contact your Authorized Service Dealer if the monitor or cable is damaged.
Y
Yvonne LarsonSep 23, 2025
What does it mean if the monitor reads “OFL” on my Toro Paint Sprayer?
- N
  nmcneilSep 23, 2025
  If the monitor on your Toro Paint Sprayer reads “OFL,” press and hold the [Reset] button to clear the monitor, because the data has exceeded the maximum allowed.
S
Sandra WoodsSep 2, 2025
Why is the speed always 0 or erratic on my Toro Sprayer?
- V
  Virginia ChambersSep 2, 2025
  If the speed is always 0 or erratic on your Toro Sprayer, connect the monitor cable. Also, calibrate the speed sensor.
B
Brandy PittsSep 4, 2025
What to do if Toro Multi Pro 1250 engine cranks, but will not start?
- S
  sjohnsonSep 4, 2025
  If your Toro Paint Sprayer engine cranks but doesn't start, the fuel tank may be empty, so fill it with fresh fuel. Also, dirt, water, or stale fuel could be in the fuel system, requiring you to drain and flush the fuel system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected, and replace the spark plug if it's damaged or dirty.
T
timothyschneiderSep 9, 2025
What to do if Toro Multi Pro 1250 Paint Sprayer displayed measurements do not make sense?
- T
  Todd FletcherSep 9, 2025
  If the displayed measurements on your Toro Paint Sprayer do not make sense, check the Units of Measurement to ensure that it is set correctly because the Units of Measurement is set to a system other than what you expect.
C
Christopher ClaySep 15, 2025
What to do if my Toro Multi Pro 1250 Paint Sprayer will not operate in either direction?
- J
  Jason JohnsonSep 15, 2025
  If the Toro Paint Sprayer does not operate in either direction, press the brake and shift the range selector into a gear. Also, release the parking brake or check the linkage.
M
Matthew BrownAug 25, 2025
What to do if Toro Paint Sprayer monitor does not display Application Rate or Total Volume?
- M
  Michael JensenAug 25, 2025
  If the monitor on your Toro Paint Sprayer does not display the Application Rate or Total Volume, connect the monitor cable if it's loose. Clean the flow meter if it's dirty or clogged. Calibrate the flow meter.