Toro 41177 User Manual (English)

Questions and Answers:

J
Jennifer ObrienAug 31, 2025
What should I do if a boom section on my Toro Sprayer does not spray?
- D
  Daniel BallAug 31, 2025
  If a boom section on your Toro Sprayer does not spray, the electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. A pinched hose can also cause this issue, so repair or replace the hose. Make sure that a boom by-pass valve is properly adjusted.
F
fnewmanAug 25, 2025
What to do if Toro 41177 distance is inaccurate?
- K
  Kimberly PaulAug 25, 2025
  If the distance measurement on your Toro Paint Sprayer is inaccurate, calibrate the speed sensor.
J
jamiehensonAug 25, 2025
What to do if Toro 41177 monitor does not display Application Rate or Total Volume?
- K
  kbrownAug 25, 2025
  If the monitor on your Toro Paint Sprayer does not display the Application Rate or Total Volume, connect the monitor cable if it's loose. Clean the flow meter if it's dirty or clogged. Calibrate the flow meter.
K
kkrauseSep 4, 2025
What to do if Toro 41177 engine cranks, but will not start?
- T
  tjohnsonSep 4, 2025
  If your Toro Paint Sprayer engine cranks but doesn't start, the fuel tank may be empty, so fill it with fresh fuel. Also, dirt, water, or stale fuel could be in the fuel system, requiring you to drain and flush the fuel system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected, and replace the spark plug if it's damaged or dirty.
C
carrmatthewSep 9, 2025
What to do if Toro 41177 Paint Sprayer displayed measurements do not make sense?
- J
  jamesmartinezSep 9, 2025
  If the displayed measurements on your Toro Paint Sprayer do not make sense, check the Units of Measurement to ensure that it is set correctly because the Units of Measurement is set to a system other than what you expect.
E
Elizabeth PriceSep 2, 2025
Why is the speed always 0 or erratic on my Toro Sprayer?
- A
  Arthur MedinaSep 2, 2025
  If the speed is always 0 or erratic on your Toro Sprayer, connect the monitor cable. Also, calibrate the speed sensor.
W
woodsusanAug 29, 2025
What to do if my Toro Sprayer engine cranks but won't start?
- C
  collinspaulAug 29, 2025
  If your Toro Sprayer's engine cranks but doesn't start, the fuel tank might be empty; refill it with fresh fuel. Also, the fuel system might contain dirt, water, or stale fuel, requiring you to drain and flush the system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected and replace any damaged or dirty spark plugs.
F
Frederick Liu DVMSep 6, 2025
Why does my Toro 41177 abnormal vibration or noise?
- D
  dylanroySep 7, 2025
  If you notice abnormal vibration or noise in your Toro Paint Sprayer, tighten the engine mounting bolts if they are loose.
D
Denise ButlerAug 27, 2025
Why is the distance reading inaccurate on my Toro 41177?
- J
  Jasmin OlsonAug 27, 2025
  If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.
J
John TannerAug 27, 2025
What to do if a boom section does not spray on my Toro 41177 Paint Sprayer?
- J
  Jordan MurrayAug 27, 2025
  If a boom section of your Toro Paint Sprayer does not spray, you can try the following: * Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it, in case the electrical connection on the boom valve is dirty or disconnected. * Check the fuses and replace them as necessary if they are blown. * Repair or replace the hose if it is pinched. * Adjust the boom by-pass valves if a boom by-pass valve is improperly adjusted. * Contact your Authorized Service Dealer if you have a damaged boom valve or damaged electrical system.