Toro 41165 - User Manual

Questions and Answers:

G
Gina JenkinsAug 31, 2025
What should I do if a boom section on my Toro Sprayer does not spray?
- H
  Holly PayneAug 31, 2025
  If a boom section on your Toro Sprayer does not spray, the electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. A pinched hose can also cause this issue, so repair or replace the hose. Make sure that a boom by-pass valve is properly adjusted.
J
Jeffrey GreenAug 25, 2025
What to do if Toro 41165 distance is inaccurate?
- A
  Adriana HughesAug 25, 2025
  If the distance measurement on your Toro Paint Sprayer is inaccurate, calibrate the speed sensor.
A
amanda09Sep 23, 2025
Why does the monitor display 6553.5 in the Application Rate setting on my Toro 41165?
- V
  vadamsSep 23, 2025
  If the monitor displays 6553.5 when in the Application Rate setting on your Toro Paint Sprayer, contact your Authorized Service Dealer, because the monitor is not receiving data from the speed sensor.
B
Brett RhodesSep 4, 2025
What to do if Toro 41165 engine cranks, but will not start?
- G
  gutierrezrachelSep 4, 2025
  If your Toro Paint Sprayer engine cranks but doesn't start, the fuel tank may be empty, so fill it with fresh fuel. Also, dirt, water, or stale fuel could be in the fuel system, requiring you to drain and flush the fuel system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected, and replace the spark plug if it's damaged or dirty.
M
Melissa RitterSep 9, 2025
What to do if Toro 41165 displayed measurements do not make sense?
- G
  Gregory HernandezSep 9, 2025
  If the displayed measurements on your Toro Paint Sprayer do not make sense, check the Units of Measurement to ensure that it is set correctly because the Units of Measurement is set to a system other than what you expect.
A
Amanda BushSep 2, 2025
Why is the speed always 0 or erratic on my Toro Sprayer?
- K
  katherine32Sep 2, 2025
  If the speed is always 0 or erratic on your Toro Sprayer, connect the monitor cable. Also, calibrate the speed sensor.
L
Linda SullivanAug 29, 2025
What to do if my Toro Sprayer engine cranks but won't start?
- E
  emeyerAug 29, 2025
  If your Toro Sprayer's engine cranks but doesn't start, the fuel tank might be empty; refill it with fresh fuel. Also, the fuel system might contain dirt, water, or stale fuel, requiring you to drain and flush the system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected and replace any damaged or dirty spark plugs.
F
Francisco JensenSep 12, 2025
Why is the speed reading always 0 or erratic on my Toro Paint Sprayer?
- S
  Scott WrightSep 12, 2025
  If the speed reading on your Toro Paint Sprayer is always 0 or erratic, it could be due to: * A loose monitor cable. Connect the monitor cable. * The speed sensor is not calibrated correctly. Calibrate the speed sensor. * The speed sensor is damaged. Contact your Authorized Service Dealer.
E
Erik FarrellSep 6, 2025
Why does my Toro 41165 Paint Sprayer abnormal vibration or noise?
- J
  Jacob MorganSep 7, 2025
  If you notice abnormal vibration or noise in your Toro Paint Sprayer, tighten the engine mounting bolts if they are loose.
A
Alexandria BurkeAug 27, 2025
Why is the distance reading inaccurate on my Toro 41165?
- E
  Emily MatthewsAug 27, 2025
  If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.