Toro 41165 - User Manual

Questions and Answers

T
Troy WebbSep 18, 2025
What to do if my Toro Paint Sprayer engine cranks but will not start?
- H
  Henry RamirezSep 18, 2025
  If your Toro Paint Sprayer engine cranks but won't start, consider these potential issues: * The fuel tank may be empty. Fill it with fresh fuel. * There might be dirt, water, or stale fuel in the fuel system. Drain and flush the fuel system, then add fresh fuel. * The fuel line could be clogged. Clean or replace it. * The spark plug lead might be disconnected. Reconnect the spark plug. * A spark plug could be damaged or dirty. Replace the spark plug. * The kill relay may not be energized; contact your Authorized Service Dealer. * The ignition could be broken; contact your Authorized Service Dealer.
G
Gina JenkinsAug 31, 2025
What should I do if a boom section on my Toro Sprayer does not spray?
- H
  Holly PayneAug 31, 2025
  If a boom section on your Toro Sprayer does not spray, the electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. A pinched hose can also cause this issue, so repair or replace the hose. Make sure that a boom by-pass valve is properly adjusted.
A
Alexandria BurkeAug 27, 2025
Why is the distance reading inaccurate on my Toro 41165?
- E
  Emily MatthewsAug 27, 2025
  If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.
D
Dwayne GoodwinSep 23, 2025
Why does the monitor not function on my Toro 41165?
- D
  davisjamesSep 23, 2025
  If the monitor on your Toro Paint Sprayer does not function, connect the monitor cable if it is loose or disconnected. Contact your Authorized Service Dealer if the monitor or cable is damaged.
J
Joseph PadillaSep 23, 2025
What does it mean if the monitor reads “OFL” on my Toro Paint Sprayer?
- L
  Lindsay FloresSep 23, 2025
  If the monitor on your Toro Paint Sprayer reads “OFL,” press and hold the [Reset] button to clear the monitor, because the data has exceeded the maximum allowed.
A
Amanda BushSep 2, 2025
Why is the speed always 0 or erratic on my Toro Sprayer?
- K
  katherine32Sep 2, 2025
  If the speed is always 0 or erratic on your Toro Sprayer, connect the monitor cable. Also, calibrate the speed sensor.
B
Brett RhodesSep 4, 2025
What to do if Toro 41165 engine cranks, but will not start?
- G
  gutierrezrachelSep 4, 2025
  If your Toro Paint Sprayer engine cranks but doesn't start, the fuel tank may be empty, so fill it with fresh fuel. Also, dirt, water, or stale fuel could be in the fuel system, requiring you to drain and flush the fuel system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected, and replace the spark plug if it's damaged or dirty.
M
Melissa RitterSep 9, 2025
What to do if Toro 41165 displayed measurements do not make sense?
- G
  Gregory HernandezSep 9, 2025
  If the displayed measurements on your Toro Paint Sprayer do not make sense, check the Units of Measurement to ensure that it is set correctly because the Units of Measurement is set to a system other than what you expect.
L
Latasha ManningSep 15, 2025
What to do if my Toro Paint Sprayer will not operate in either direction?
- L
  Laurie BowmanSep 16, 2025
  If the Toro Paint Sprayer does not operate in either direction, press the brake and shift the range selector into a gear. Also, release the parking brake or check the linkage.
C
Cole FrostAug 25, 2025
What to do if Toro 41165 monitor does not display Application Rate or Total Volume?
- G
  gutierrezmichaelAug 26, 2025
  If the monitor on your Toro Paint Sprayer does not display the Application Rate or Total Volume, connect the monitor cable if it's loose. Clean the flow meter if it's dirty or clogged. Calibrate the flow meter.