What to do if Toro Paint Sprayer will not operate in either direction?
If your Toro Paint Sprayer won't operate in either direction, first ensure the parking brake is released or check the linkage. If this doesn't solve the problem, it could be a broken transmission, control linkage needing adjustment or replacement, or damage to the drive shaft or wheel hub key, in which case you should contact your Authorized Service Dealer.
Why does my Toro Paint Sprayer console computer display a flashing Cal when turning the master switch on or off?
If your Toro Paint Sprayer displays a flashing 'Cal' when you turn the master switch to the On or Off position, it typically points to battery issues. Check that the battery connections are secure, and then check the battery voltage.
Why does the Toro 41086 console computer display a flashing Cal when I change the speed?
If the console computer on your Toro Paint Sprayer shows a flashing 'Cal' when you change the speed, it's likely due to battery issues. Make sure the battery connections are secure and verify the battery voltage.
What to do if Toro 41086 Paint Sprayer engine cranks but will not start?
If your Toro Paint Sprayer's engine cranks but doesn't start, several factors could be at play. First, ensure the fuel tank isn't empty by filling it with fresh fuel. If the fuel system contains dirt, water, or stale fuel, drain and flush the system before adding fresh fuel. A clogged fuel line could also be the culprit, so clean or replace it. Check that the spark plug lead is connected and that the spark plug isn't damaged or dirty; reconnect or replace as needed. If these steps don't resolve the issue, it's possible that the kill relay is not energized or the ignition is broken, in which case you should contact an Authorized Service Dealer.
Why Toro Paint Sprayer engine starts, but does not keep running?
If your Toro Paint Sprayer engine starts but doesn't keep running, several issues could be the cause. Start by checking the fuel tank vent; if it's restricted, replace the fuel cap. Also, dirt or water in the fuel system can cause this problem, so drain and flush the fuel system and add fresh fuel. A clogged fuel filter could also be the issue, so replace it. Check for a blown or loose fuse, and correct or replace it as necessary. If the problem persists, there may be loose wires or poor connections; check and tighten the wire connections. If these steps don't solve the issue, it's possible that the fuel pump or carburetor is broken, or the cylinder head gasket is broken, in which case you should contact an Authorized Service Dealer.
What to do if my Toro 41086 engine loses power?
If your Toro Paint Sprayer engine loses power, start by checking the crankcase oil level and fill or drain to the correct level. A dirty air cleaner element can also cause this, so clean or replace it. If there's dirt, water, or stale fuel in the fuel system, drain and flush it, then add fresh fuel. Also, a damaged or dirty spark plug can cause power loss, so replace it. If the vent hole in the fuel tank vent fitting is plugged, replace the fuel cap. If these steps don't resolve the issue, it might be overheating. For overheating see 'Engine Overheats'. Otherwise, it is possible that there is low compression, in which case you should contact an Authorized Service Dealer.
What to do if Toro 41086 Paint Sprayer has no display lights with the power on?
If your Toro Paint Sprayer's display lights are not working when powered on, several factors could be at play. First, check the fuse on the back of the console computer and replace it if it's blown. Next, ensure that the battery connections are secure. If the issue persists, the power switch might be faulty and require repair or replacement. As a last resort, the processor board assembly may have a problem, and you should have an Authorized Distributor replace it.
Why is the rate inaccurate or unstable on my Toro 41086 Paint Sprayer?
An inaccurate or unstable rate on your Toro Paint Sprayer can stem from several causes. First, ensure that all numbers entered into the console computer are correct. Verify that the wheel drive setting is set to SP3 and that the Speed Cal number is correct. Also, check that the flowmeter is pointing in the direction of flow and that the nozzles are appropriate for the rate setting. If adjusting the pressure in manual mode with the agitation on and the booms off is difficult in the high end of the pressure range, verify the voltage at the valve connector. Ensure the Valve Cal number is properly set. If problems persist, the processor board assembly may need replacement by an Authorized Distributor.
What to do if a boom section does not spray on my Toro 41086 Paint Sprayer?
If a boom section on your Toro Paint Sprayer isn't spraying, start by checking the electrical connection on the boom valve for dirt or disconnection. Turn the valve off manually, disconnect the electrical connector, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. Inspect for a pinched hose and repair or replace it. Ensure the boom by-pass valve is properly adjusted. If these steps don't resolve the issue, the boom valve or electrical system may be damaged, in which case you should contact your Authorized Service Dealer.
What to do if Toro 41086 has abnormal vibration or noise?
If your Toro Paint Sprayer is experiencing abnormal vibration or noise, check the engine mounting bolts and tighten them, as they may be loose.
General| Brand | Toro |
|---|---|
| Model | 41086 |
| Category | Paint Sprayer |
| Language | English |
To Next Page
