Toro 41086 - User Manual

Questions and Answers:

P
Philip GregorySep 2, 2025
How to fix Toro 41086 engine that will not idle?
- T
  Tanya BarkerSep 2, 2025
  If your Toro Paint Sprayer engine won't idle, start by checking if the fuel tank vent is restricted and replace the fuel cap if necessary. Also, check for dirt, water, or stale fuel in the fuel system, and drain and flush the system, adding fresh fuel. A damaged or broken spark plug can also cause idling issues, so replace it. If these steps don't resolve the problem, the carburetor idle passages may be plugged, the idle speed adjusting screw may be incorrectly set, the fuel pump may be broken, there may be low compression, or the air cleaner element may be dirty, in which case you should contact an Authorized Service Dealer. But if the air cleaner element is dirty, you can also clean or replace it.
D
Daniel Sherman IISep 1, 2025
What to do if Toro 41086 has abnormal vibration or noise?
- H
  hmendezSep 1, 2025
  If your Toro Paint Sprayer is experiencing abnormal vibration or noise, check the engine mounting bolts and tighten them, as they may be loose.
C
Cameron HinesAug 31, 2025
What to do if Toro 41086 engine runs, but knocks or misses?
- B
  blackjohnAug 31, 2025
  If your Toro Paint Sprayer engine runs but knocks or misses, it could be due to several reasons. Start by checking for dirt, water, or stale fuel in the fuel system; if present, drain and flush the system and add fresh fuel. A loose spark plug lead can also cause this, so reconnect it. Additionally, a broken spark plug can be the problem, so replace it. Check for loose wires or poor connections and tighten them. If the issue persists, the engine may be overheating, see Engine Overheats.
K
Kevin PhillipsAug 30, 2025
Why Toro 41086 starter does not crank?
- R
  Reginald RiveraAug 30, 2025
  If the starter on your Toro Paint Sprayer isn't cranking, there are several potential causes. First, ensure the traction pedal is in Neutral by releasing it. Check the electrical connections for corrosion or looseness, ensuring they have good contact. Also, inspect the fuse to see if it's blown or loose, and correct or replace it as needed. If the battery is discharged, charge or replace it. If the issue persists, the safety interlock system may be malfunctioning, or there could be a broken starter or starter solenoid, or seized internal engine components, in which case you should contact your Authorized Service Dealer.
C
Christopher YoungAug 29, 2025
What to do if Toro 41086 engine overheats?
- L
  Lauren OrtegaAug 29, 2025
  If your Toro Paint Sprayer engine overheats, first check the crankcase oil level and fill or drain to the full mark as needed. Excessive loading can also cause overheating, so reduce the load and use a lower ground speed. Make sure the radiator is clean, cleaning it with every use. Additionally, check the coolant level and add coolant if it's low. If the fuel mixture is lean, contact your Authorized Service Dealer.
M
Michael RomeroAug 28, 2025
What to do if my Toro 41086 engine loses power?
- C
  Charles Lopez IIAug 28, 2025
  If your Toro Paint Sprayer engine loses power, start by checking the crankcase oil level and fill or drain to the correct level. A dirty air cleaner element can also cause this, so clean or replace it. If there's dirt, water, or stale fuel in the fuel system, drain and flush it, then add fresh fuel. Also, a damaged or dirty spark plug can cause power loss, so replace it. If the vent hole in the fuel tank vent fitting is plugged, replace the fuel cap. If these steps don't resolve the issue, it might be overheating. For overheating see 'Engine Overheats'. Otherwise, it is possible that there is low compression, in which case you should contact an Authorized Service Dealer.
H
hatfieldjimmyAug 27, 2025
Why Toro Paint Sprayer engine starts, but does not keep running?
- B
  Beth GarciaAug 27, 2025
  If your Toro Paint Sprayer engine starts but doesn't keep running, several issues could be the cause. Start by checking the fuel tank vent; if it's restricted, replace the fuel cap. Also, dirt or water in the fuel system can cause this problem, so drain and flush the fuel system and add fresh fuel. A clogged fuel filter could also be the issue, so replace it. Check for a blown or loose fuse, and correct or replace it as necessary. If the problem persists, there may be loose wires or poor connections; check and tighten the wire connections. If these steps don't solve the issue, it's possible that the fuel pump or carburetor is broken, or the cylinder head gasket is broken, in which case you should contact an Authorized Service Dealer.
J
Julie AndersonAug 27, 2025
What to do if Toro 41086 Paint Sprayer engine cranks but will not start?
- R
  Ryan PerkinsAug 27, 2025
  If your Toro Paint Sprayer's engine cranks but doesn't start, several factors could be at play. First, ensure the fuel tank isn't empty by filling it with fresh fuel. If the fuel system contains dirt, water, or stale fuel, drain and flush the system before adding fresh fuel. A clogged fuel line could also be the culprit, so clean or replace it. Check that the spark plug lead is connected and that the spark plug isn't damaged or dirty; reconnect or replace as needed. If these steps don't resolve the issue, it's possible that the kill relay is not energized or the ignition is broken, in which case you should contact an Authorized Service Dealer.
D
Darlene SchneiderAug 25, 2025
Why does the Toro 41086 console computer display a flashing Cal when I change the speed?
- R
  Rebecca MillerAug 26, 2025
  If the console computer on your Toro Paint Sprayer shows a flashing 'Cal' when you change the speed, it's likely due to battery issues. Make sure the battery connections are secure and verify the battery voltage.
R
Ryan RamirezAug 25, 2025
Why does my Toro Paint Sprayer console computer display a flashing Cal when turning the master switch on or off?
- G
  Gary LevyAug 25, 2025
  If your Toro Paint Sprayer displays a flashing 'Cal' when you turn the master switch to the On or Off position, it typically points to battery issues. Check that the battery connections are secure, and then check the battery voltage.