Toro 41568 - User Manual

Questions and Answers

W
wendy01Sep 17, 2025
Why does the speed display read 0 on my Toro 41568?
- C
  charlesrichSep 18, 2025
  If the speed display on your Toro Paint Sprayer reads '0', the pins on the speed sensor cable connector and the plug on the back of the console computer might be loose, and you should have an Authorized Distributor repair or replace the connector or plug. The pins and sockets on the speed sensor cable could also be dirty, so try cleaning them. If neither of those fixes the issue, there may be a problem with the speed sensor switch assembly, which an Authorized Distributor would need to replace.
M
Melissa ScottAug 25, 2025
Why does my Toro 41568 Paint Sprayer console computer display a flashing Cal when turning the master switch on or off?
- A
  Alex EdwardsAug 25, 2025
  If your Toro Paint Sprayer displays a flashing 'Cal' when you turn the master switch to the On or Off position, it typically points to battery issues. Check that the battery connections are secure, and then check the battery voltage.
D
Donna ClarkAug 25, 2025
Why does the Toro Paint Sprayer console computer display a flashing Cal when I change the speed?
- S
  Sarah GoodmanAug 26, 2025
  If the console computer on your Toro Paint Sprayer shows a flashing 'Cal' when you change the speed, it's likely due to battery issues. Make sure the battery connections are secure and verify the battery voltage.
C
Carolyn RandallAug 27, 2025
What to do if Toro 41568 Paint Sprayer engine cranks but will not start?
- I
  igreenAug 27, 2025
  If your Toro Paint Sprayer's engine cranks but doesn't start, several factors could be at play. First, ensure the fuel tank isn't empty by filling it with fresh fuel. If the fuel system contains dirt, water, or stale fuel, drain and flush the system before adding fresh fuel. A clogged fuel line could also be the culprit, so clean or replace it. Check that the spark plug lead is connected and that the spark plug isn't damaged or dirty; reconnect or replace as needed. If these steps don't resolve the issue, it's possible that the kill relay is not energized or the ignition is broken, in which case you should contact an Authorized Service Dealer.
A
Aaron FinleySep 18, 2025
Why are all keyboard lights on at the same time on my Toro Paint Sprayer?
- B
  Brandy BoydSep 18, 2025
  If all the keyboard lights on your Toro Paint Sprayer are illuminated simultaneously, it indicates a problem with the face plate sub assembly, which should be replaced by an Authorized Distributor.
T
Tammy LynchSep 23, 2025
Why does one display digit have one or more missing segments on my Toro 41568?
- D
  Dr. Natasha BryanSep 23, 2025
  If one of the display digits on your Toro Paint Sprayer has missing segments, this indicates a problem with the LCD display board assembly, which should be replaced by an Authorized Distributor.
K
kalvaradoSep 9, 2025
What to do if Toro Paint Sprayer has no display lights with the power on?
- X
  xjordanSep 9, 2025
  If your Toro Paint Sprayer's display lights are not working when powered on, several factors could be at play. First, check the fuse on the back of the console computer and replace it if it's blown. Next, ensure that the battery connections are secure. If the issue persists, the power switch might be faulty and require repair or replacement. As a last resort, the processor board assembly may have a problem, and you should have an Authorized Distributor replace it.
S
sean43Sep 10, 2025
Why is the rate inaccurate or unstable on my Toro 41568 Paint Sprayer?
- B
  burnslaurenSep 12, 2025
  An inaccurate or unstable rate on your Toro Paint Sprayer can stem from several causes. First, ensure that all numbers entered into the console computer are correct. Verify that the wheel drive setting is set to SP3 and that the Speed Cal number is correct. Also, check that the flowmeter is pointing in the direction of flow and that the nozzles are appropriate for the rate setting. If adjusting the pressure in manual mode with the agitation on and the booms off is difficult in the high end of the pressure range, verify the voltage at the valve connector. Ensure the Valve Cal number is properly set. If problems persist, the processor board assembly may need replacement by an Authorized Distributor.
M
Monica VaughnSep 3, 2025
What to do if a boom section does not spray on my Toro Paint Sprayer?
- T
  Thomas FoxSep 3, 2025
  If a boom section on your Toro Paint Sprayer isn't spraying, start by checking the electrical connection on the boom valve for dirt or disconnection. Turn the valve off manually, disconnect the electrical connector, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. Inspect for a pinched hose and repair or replace it. Ensure the boom by-pass valve is properly adjusted. If these steps don't resolve the issue, the boom valve or electrical system may be damaged, in which case you should contact your Authorized Service Dealer.
L
lori96Sep 1, 2025
What to do if Toro 41568 has abnormal vibration or noise?
- S
  Shawn SwansonSep 1, 2025
  If your Toro Paint Sprayer is experiencing abnormal vibration or noise, check the engine mounting bolts and tighten them, as they may be loose.