Toro 41568 - User Manual

Questions and Answers

D
dylan41Sep 12, 2025
What to do if I cannot vary the rate in manual or automatic mode on my Toro 41568 Paint Sprayer?
- D
  daniel40Sep 12, 2025
  If you're unable to adjust the rate in either manual or automatic mode on your Toro Paint Sprayer, begin by checking the cable leading to the hydraulic control valve for any breaks; if breaks are present, replace the cable. Inspect the connections in the cable line for dirt and clean or replace the cable line if necessary. Verify that there is voltage at the valve connector by placing the Master switch to the Man position with the booms in the Off position and the power switch to the On position, then manually operate the Incr/Decr switch to verify the voltage. If the issue persists, the Rate Inc/Dec switch might be faulty and require replacement.
D
david26Sep 12, 2025
How to fix inaccurate or unstable speed on Toro 41568?
- D
  derekmartinezSep 12, 2025
  If the speed on your Toro Paint Sprayer is inaccurate or unstable, there are a couple of things you can check. Make sure the wheel drive setting is set to SP3. Also, verify that you've entered the correct Speed Cal number.
S
sean43Sep 10, 2025
Why is the rate inaccurate or unstable on my Toro 41568 Paint Sprayer?
- B
  burnslaurenSep 12, 2025
  An inaccurate or unstable rate on your Toro Paint Sprayer can stem from several causes. First, ensure that all numbers entered into the console computer are correct. Verify that the wheel drive setting is set to SP3 and that the Speed Cal number is correct. Also, check that the flowmeter is pointing in the direction of flow and that the nozzles are appropriate for the rate setting. If adjusting the pressure in manual mode with the agitation on and the booms off is difficult in the high end of the pressure range, verify the voltage at the valve connector. Ensure the Valve Cal number is properly set. If problems persist, the processor board assembly may need replacement by an Authorized Distributor.
K
kalvaradoSep 9, 2025
What to do if Toro Paint Sprayer has no display lights with the power on?
- X
  xjordanSep 9, 2025
  If your Toro Paint Sprayer's display lights are not working when powered on, several factors could be at play. First, check the fuse on the back of the console computer and replace it if it's blown. Next, ensure that the battery connections are secure. If the issue persists, the power switch might be faulty and require repair or replacement. As a last resort, the processor board assembly may have a problem, and you should have an Authorized Distributor replace it.
J
julia38Sep 8, 2025
What to do if a boom section does not turn off on my Toro 41568?
- M
  Melissa SampsonSep 8, 2025
  If a boom section doesn't turn off on your Toro Paint Sprayer, the valve is likely damaged. Stop the spray system and pump, and turn off the sprayer. Remove the retainer from under the boom valve and pull out the motor and stem. Inspect all parts and replace any that appear damaged.
W
wadamsAug 23, 2025
Why does the Toro 41568 console computer display a flashing Cal when I start the engine?
- J
  John GreerAug 23, 2025
  A flashing 'Cal' on your Toro Paint Sprayer's console computer when starting the engine usually indicates an issue with the battery connections or voltage. Ensure that the battery connections are secure and check the battery voltage to make sure it's sufficient.
J
Joseph PaulSep 6, 2025
What causes a pressure increase when you turn on a boom on Toro 41568?
- K
  Kevin VaughnSep 6, 2025
  A pressure increase when you turn on a boom on your Toro Paint Sprayer is caused by a clogged nozzle filter. Remove and clean all nozzles.
J
james24Sep 5, 2025
What causes a pressure drop when you turn on a boom on Toro 41568?
- M
  Mrs. Alyssa SmithSep 5, 2025
  A pressure drop when you turn on a boom in your Toro Paint Sprayer can be caused by an improperly adjusted boom bypass valve. Adjust the boom bypass valve. Another cause could be an obstruction in the boom valve body. Remove the inlet and outlet connections to the boom valve and remove any obstructions.
G
George BellSep 4, 2025
What to do if Toro 41568 will not operate in either direction?
- M
  Manuel BensonSep 4, 2025
  If your Toro Paint Sprayer won't operate in either direction, first ensure the parking brake is released or check the linkage. If this doesn't solve the problem, it could be a broken transmission, control linkage needing adjustment or replacement, or damage to the drive shaft or wheel hub key, in which case you should contact your Authorized Service Dealer.
M
Monica VaughnSep 3, 2025
What to do if a boom section does not spray on my Toro Paint Sprayer?
- T
  Thomas FoxSep 3, 2025
  If a boom section on your Toro Paint Sprayer isn't spraying, start by checking the electrical connection on the boom valve for dirt or disconnection. Turn the valve off manually, disconnect the electrical connector, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. Inspect for a pinched hose and repair or replace it. Ensure the boom by-pass valve is properly adjusted. If these steps don't resolve the issue, the boom valve or electrical system may be damaged, in which case you should contact your Authorized Service Dealer.