Toro 41086 - User Manual

Questions and Answers

E
Erica PearsonSep 12, 2025
What to do if I cannot vary the rate in manual or automatic mode on my Toro 41086 Paint Sprayer?
- E
  elizabethdixonSep 12, 2025
  If you're unable to adjust the rate in either manual or automatic mode on your Toro Paint Sprayer, begin by checking the cable leading to the hydraulic control valve for any breaks; if breaks are present, replace the cable. Inspect the connections in the cable line for dirt and clean or replace the cable line if necessary. Verify that there is voltage at the valve connector by placing the Master switch to the Man position with the booms in the Off position and the power switch to the On position, then manually operate the Incr/Decr switch to verify the voltage. If the issue persists, the Rate Inc/Dec switch might be faulty and require replacement.
J
Jessica RomeroSep 12, 2025
How to fix inaccurate or unstable speed on Toro 41086 Paint Sprayer?
- C
  Crystal VincentSep 12, 2025
  If the speed on your Toro Paint Sprayer is inaccurate or unstable, there are a couple of things you can check. Make sure the wheel drive setting is set to SP3. Also, verify that you've entered the correct Speed Cal number.
R
Robert MaySep 10, 2025
Why is the rate inaccurate or unstable on my Toro 41086 Paint Sprayer?
- J
  James GuerreroSep 10, 2025
  An inaccurate or unstable rate on your Toro Paint Sprayer can stem from several causes. First, ensure that all numbers entered into the console computer are correct. Verify that the wheel drive setting is set to SP3 and that the Speed Cal number is correct. Also, check that the flowmeter is pointing in the direction of flow and that the nozzles are appropriate for the rate setting. If adjusting the pressure in manual mode with the agitation on and the booms off is difficult in the high end of the pressure range, verify the voltage at the valve connector. Ensure the Valve Cal number is properly set. If problems persist, the processor board assembly may need replacement by an Authorized Distributor.
L
Lori SmithSep 9, 2025
What to do if Toro 41086 Paint Sprayer has no display lights with the power on?
- J
  John GlassSep 9, 2025
  If your Toro Paint Sprayer's display lights are not working when powered on, several factors could be at play. First, check the fuse on the back of the console computer and replace it if it's blown. Next, ensure that the battery connections are secure. If the issue persists, the power switch might be faulty and require repair or replacement. As a last resort, the processor board assembly may have a problem, and you should have an Authorized Distributor replace it.
M
Martin WalkerSep 8, 2025
What to do if a boom section does not turn off on my Toro 41086 Paint Sprayer?
- A
  acostatimothySep 8, 2025
  If a boom section doesn't turn off on your Toro Paint Sprayer, the valve is likely damaged. Stop the spray system and pump, and turn off the sprayer. Remove the retainer from under the boom valve and pull out the motor and stem. Inspect all parts and replace any that appear damaged.
M
Melissa DominguezAug 23, 2025
Why does the Toro 41086 Paint Sprayer console computer display a flashing Cal when I start the engine?
- C
  cynthia12Aug 23, 2025
  A flashing 'Cal' on your Toro Paint Sprayer's console computer when starting the engine usually indicates an issue with the battery connections or voltage. Ensure that the battery connections are secure and check the battery voltage to make sure it's sufficient.
J
jporterSep 6, 2025
What causes a pressure increase when you turn on a boom on Toro 41086?
- B
  bcookSep 6, 2025
  A pressure increase when you turn on a boom on your Toro Paint Sprayer is caused by a clogged nozzle filter. Remove and clean all nozzles.
K
Kelli MaloneSep 5, 2025
What causes a pressure drop when you turn on a boom on Toro 41086 Paint Sprayer?
- M
  Michael RiveraSep 5, 2025
  A pressure drop when you turn on a boom in your Toro Paint Sprayer can be caused by an improperly adjusted boom bypass valve. Adjust the boom bypass valve. Another cause could be an obstruction in the boom valve body. Remove the inlet and outlet connections to the boom valve and remove any obstructions.
J
Jessica BrownSep 4, 2025
What to do if Toro Paint Sprayer will not operate in either direction?
- A
  Anna ColonSep 4, 2025
  If your Toro Paint Sprayer won't operate in either direction, first ensure the parking brake is released or check the linkage. If this doesn't solve the problem, it could be a broken transmission, control linkage needing adjustment or replacement, or damage to the drive shaft or wheel hub key, in which case you should contact your Authorized Service Dealer.
J
joseph13Sep 3, 2025
What to do if a boom section does not spray on my Toro 41086 Paint Sprayer?
- D
  Daniel TownsendSep 3, 2025
  If a boom section on your Toro Paint Sprayer isn't spraying, start by checking the electrical connection on the boom valve for dirt or disconnection. Turn the valve off manually, disconnect the electrical connector, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. Inspect for a pinched hose and repair or replace it. Ensure the boom by-pass valve is properly adjusted. If these steps don't resolve the issue, the boom valve or electrical system may be damaged, in which case you should contact your Authorized Service Dealer.