Why does my Toro Sprayer engine run, but knocks or misses?
If your Toro Sprayer's engine runs but knocks or misses, it could be due to dirt, water, or stale fuel in the fuel system. In this case, drain and flush the fuel system, then add fresh fuel. Also, a loose spark plug lead could be the issue; reconnect it. Replacing a broken spark plug might also solve the problem. Make sure to check and tighten any loose wire connections.
How do I resolve abnormal vibration or noise in my Toro Sprayer?
Abnormal vibration or noise in your Toro Sprayer may be due to loose engine mounting bolts. Make sure to tighten the engine mounting bolts.
What causes a pressure drop when turning on a boom in my Toro Sprayer?
A pressure drop when you turn on a boom in your Toro Sprayer can be caused by an improperly adjusted boom bypass valve, so adjust the boom bypass valve. Additionally, check for obstructions in the boom valve body by removing the inlet and outlet connections to the boom valve and removing any obstructions. Inspect all nozzles for damage or clogs.
Why does my Toro 41165 engine run, but knocks or misses?
If your Toro Paint Sprayer engine runs but knocks or misses, here are some things to check: * Ensure that there is no dirt, water, or stale fuel in the fuel system by draining and flushing it, then adding fresh fuel. * Make sure the spark plug lead is securely connected. Reconnect it if it's loose. * Replace the spark plug if it's broken. * Check and tighten any loose wires or poor connections. * Refer to the 'Engine Overheats' section if the engine is overheating.
What causes a boom section not to turn off on my Toro 41165?
If a boom section on your Toro Paint Sprayer does not turn off, stop the spray system and pump, and turn off the sprayer. Remove the retainer from under the boom valve and pull out the motor and stem. Inspect all parts and replace any that appear damaged, because the valve may be damaged.
What causes a pressure drop when turning on a boom on my Toro 41165 Paint Sprayer?
A pressure drop when you turn on a boom on your Toro Paint Sprayer may occur because: * The boom bypass valve is improperly adjusted. Adjust the boom bypass valve. * There is an obstruction in the boom valve body. Remove the inlet and outlet connections to the boom valve and remove any obstructions. * A nozzle filter is damaged or clogged. Remove and inspect all nozzles.
What should I do if a boom section on my Toro Sprayer does not spray?
If a boom section on your Toro Sprayer does not spray, the electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it. Also, check the fuses and replace them if necessary. A pinched hose can also cause this issue, so repair or replace the hose. Make sure that a boom by-pass valve is properly adjusted.
What to do if my Toro Sprayer machine will not operate or is sluggish?
If your Toro Sprayer machine will not operate or is sluggish because the engine bogs down or stalls, make sure that the parking brake is released.
What to do if my Toro Sprayer machine will not operate in either direction?
If your Toro Sprayer machine will not operate in either direction, ensure the range selector is not in the Neutral position by pressing the brake and shifting the range selector into a gear. Also, verify that the parking brake was released or is releasing; if not, release the parking brake or check the linkage.
What should I do if a boom section on my Toro Sprayer does not turn off?
If a boom section on your Toro Sprayer does not turn off, stop the spray system and pump, and turn off the sprayer. Remove the retainer from under the boom valve and pull out the motor and stem. Inspect all parts and replace any that appear damaged.
General| Power Source | Electric |
|---|---|
| Spray Pattern | Adjustable |
| Type | Airless |
| Maximum Pressure | 3000 psi |
| Hose Length | 25 ft |
| Tip Size | 0.015 in |
| Voltage | 120 V |
To Next Page
