Toro 41177 User Manual (English)

Questions and Answers:

J
John TannerAug 27, 2025
What to do if a boom section does not spray on my Toro 41177 Paint Sprayer?
- J
  Jordan MurrayAug 27, 2025
  If a boom section of your Toro Paint Sprayer does not spray, you can try the following: * Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, and then reconnect it, in case the electrical connection on the boom valve is dirty or disconnected. * Check the fuses and replace them as necessary if they are blown. * Repair or replace the hose if it is pinched. * Adjust the boom by-pass valves if a boom by-pass valve is improperly adjusted. * Contact your Authorized Service Dealer if you have a damaged boom valve or damaged electrical system.
D
Denise ButlerAug 27, 2025
Why is the distance reading inaccurate on my Toro 41177?
- J
  Jasmin OlsonAug 27, 2025
  If the distance measurement is inaccurate on your Toro Paint Sprayer, calibrate the speed sensor.
E
Emma CunninghamSep 2, 2025
How do I fix inaccurate distance readings on my Toro Sprayer?
- J
  Joseph MillerSep 2, 2025
  If the distance is inaccurate on your Toro Sprayer, calibrate the speed sensor.
K
kkrauseSep 4, 2025
What to do if Toro 41177 engine cranks, but will not start?
- T
  tjohnsonSep 4, 2025
  If your Toro Paint Sprayer engine cranks but doesn't start, the fuel tank may be empty, so fill it with fresh fuel. Also, dirt, water, or stale fuel could be in the fuel system, requiring you to drain and flush the fuel system and add fresh fuel. Check for a clogged fuel line and clean or replace it if necessary. Ensure the spark plug lead is connected, and replace the spark plug if it's damaged or dirty.
F
Frederick Liu DVMSep 6, 2025
Why does my Toro 41177 abnormal vibration or noise?
- D
  dylanroySep 7, 2025
  If you notice abnormal vibration or noise in your Toro Paint Sprayer, tighten the engine mounting bolts if they are loose.
A
Alicia HatfieldSep 9, 2025
What to do if Toro Paint Sprayer engine cranks but will not start?
- L
  Lawrence RobertsonSep 9, 2025
  If your Toro Paint Sprayer's engine cranks but doesn't start, here's what you can check: * Ensure the fuel tank isn't empty by filling it with fresh fuel. * The fuel system might have dirt, water, or stale fuel. In this case, drain and flush the fuel system and add fresh fuel. * A clogged fuel line could be the issue, so clean or replace it. * Make sure the spark plug lead is connected. * Replace the spark plug if it's damaged or dirty. * If the kill relay is not energized or the ignition is broken, contact your Authorized Service Dealer.
A
Anthony AustinAug 26, 2025
Why is the area measurement inaccurate on my Toro 41177 Paint Sprayer?
- J
  jamesmartinezAug 26, 2025
  The area measurement on your Toro Paint Sprayer could be inaccurate because: * The sprayer width is not correctly entered. Check and set the appropriate Width in the calibration mode. * The speed sensor is not calibrated correctly. Calibrate the speed sensor. * The speed sensor is damaged. Contact your Authorized Service Dealer.
D
david88Aug 25, 2025
What to do if Toro Paint Sprayer Total Volume is inaccurate?
- D
  David KeithAug 26, 2025
  If the total volume on your Toro Paint Sprayer is inaccurate, clean the flow meter if it's dirty or clogged. Calibrate the flow meter.
J
jamiehensonAug 25, 2025
What to do if Toro 41177 monitor does not display Application Rate or Total Volume?
- K
  kbrownAug 25, 2025
  If the monitor on your Toro Paint Sprayer does not display the Application Rate or Total Volume, connect the monitor cable if it's loose. Clean the flow meter if it's dirty or clogged. Calibrate the flow meter.
F
fnewmanAug 25, 2025
What to do if Toro 41177 distance is inaccurate?
- K
  Kimberly PaulAug 25, 2025
  If the distance measurement on your Toro Paint Sprayer is inaccurate, calibrate the speed sensor.