Toro 72946 User Manual (English)

Questions and Answers:

K
Kevin RothSep 2, 2025
What to do if Toro 72946 Lawn Mower produces an uneven cutting height?
- J
  jennifer95Sep 2, 2025
  If your Toro Lawn Mower is producing an uneven cutting height, consider these potential causes: 1. The blades might not be sharp enough, so sharpen them. 2. The cutting blades could be bent, in which case you should install new ones. 3. The mower deck may not be level; level it from side-to-side and front-to-rear. 4. The underside of the mower might be dirty, so clean it. 5. Check and adjust the tire pressure to the correct levels. If the blade spindle is bent, contact an Authorized Service Dealer.
J
josephorozcoSep 2, 2025
What to do if my Toro Lawn Mower won't drive?
- K
  Kevin JohnsonSep 2, 2025
  If your Toro Lawn Mower isn't driving, check if the bypass valves are not closed tight and tighten them. Also, the pump belt could be worn, loose, or broken, or off a pulley, in which case change the belt. The idler spring might be broken or missing, so replace the spring. The hydraulic-fluid level might be low or too hot, so add hydraulic fluid to reservoirs or let it cool down.
J
jgonzalesSep 2, 2025
How to troubleshoot uneven cutting height on my Toro Lawn Mower?
- A
  Amy GrahamSep 2, 2025
  An uneven cutting height on your Toro Lawn Mower could be due to several factors. The blade(s) might not be sharp, so sharpen them. Alternatively, the cutting blade(s) could be bent, so install new cutting blade(s). The mower deck might not be level, so level the mower deck from side-to-side and front-to-rear. The underside of the mower could be dirty, so clean it. Also, the tire pressure might not be correct, so adjust it.
A
Alexandra BradleyAug 25, 2025
Why does my Toro 72946 Lawn Mower engine not start, start hard, or fail to keep running?
- L
  Lauren PetersonAug 25, 2025
  Several factors can cause your Toro Lawn Mower engine to fail to start, start with difficulty, or stall. Here are a few things to check: * Ensure the fuel tank is full. * Verify the fuel-shutoff valve is open. * Check that the oil level in the crankcase is adequate. * Position the throttle control midway between the slow and fast positions. * Replace a dirty fuel filter. * Clean or replace the air-cleaner element. * Check the spark-plug wire connection and adjust or replace the spark plug, if needed. Also, inspect the seat-switch indicator and replace the seat if necessary and check the electrical connections for good contact, cleaning them with electrical-contact cleaner and applying dielectric grease.
C
cowanstephanieSep 1, 2025
How to fix uneven cutting height on my Toro 72946?
- K
  Kimberly MoralesSep 1, 2025
  If the cutting height is uneven on your Toro Lawn Mower, consider these possibilities: * Sharpen the blade(s) if they are not sharp. * Install a new cutting blade(s) if the current ones are bent. * Level the mower from side-to-side and front-to-rear. * Adjust the anti-scalp wheel height if an anti-scalp roller (if applicable) is not set correctly. * Clean the underside of the mower deck if it is dirty. * Adjust the tire pressure if it is incorrect.
T
tiffanyboothSep 1, 2025
How to fix a starter that won't crank on my Toro 72946?
- W
  washingtonlouisSep 1, 2025
  If the starter on your Toro Lawn Mower won't crank, check these items: * Ensure the blade-control switch is disengaged. * Engage the parking brake. * Move the motion-control levers to the NEUTRAL-LOCK position. * Make sure you are sitting in the operator’s seat. * Charge the battery if it's dead. * Check the electrical connections for good contact. * Replace the fuse if it's blown.
W
william61Sep 1, 2025
Why does my Toro 72946 have an uneven cutting height?
- J
  Jade WilliamsonSep 1, 2025
  An uneven cutting height on your Toro lawn mower can result from: - Dull blades: Sharpen the blade(s). - Bent cutting blades: Install new cutting blade(s). - Unlevel mower deck: Level mower deck from side-to-side and front-to-rear. - Dirty mower underside: Clean the underside of the mower. - Incorrect tire pressure: Adjust the tire pressure.
N
Nancy ParkerAug 31, 2025
How to fix Toro 72946 Lawn Mower engine when it loses power?
- J
  Justin BaileySep 1, 2025
  If your Toro lawn mower engine loses power, try reducing the ground speed, as the engine load may be excessive. Check and clean the air cleaner element if it's dirty. Ensure the oil level in the crankcase is sufficient. Clear any obstructions from the cooling fins and air passages above the engine. Also, inspect the fuel cap vent hole and clean or replace the fuel cap if it's plugged, and replace the fuel filter if it is dirty.
X
xhernandezAug 31, 2025
What to do if my Toro 72946 Lawn Mower will not drive?
- T
  Timothy YatesAug 31, 2025
  If your Toro Lawn Mower won't drive, consider the following: * Tighten the by pass valves. * Change the belt. * Replace the spring. * Add hydraulic oil to reservoirs or let it cool down.
T
Timothy RussellAug 31, 2025
What to do if my Toro 72946 Lawn Mower blades do not rotate?
- Z
  Zachary CombsAug 31, 2025
  If the blades on your Toro Lawn Mower do not rotate, try these solutions: * Install a new deck belt. * Install the mower deck pulley and check the idler pulley, idler arm, and spring for correct position and function. * Check the belt tension or install a new belt. * Replace the spring.