Need help?Do you have a question about the Toro Groundsmaster 7210 Series and is the answer not in the manual?
General| Drive System | 2WD |
|---|---|
| Number of Blades | 3 |
| Horsepower | 24.8 hp (18.5 kW) |
| Transmission | Hydrostatic |
| Cutting Height | 1-5 in (2.5-12.7 cm) |
| Engine Displacement | 1123 cc |
Verify that all parts have been shipped by using the provided chart.
Procedure to raise the roll bar, referring to specific page for details.
Procedure to install the mower deck using separate installation instructions.
Adjust the left, front caster wheel to the outside or inside position based on deck size.
Procedure to check tire pressure, referencing a specific page for instructions.
Check hydraulic fluid, engine oil, and cooling system levels before starting.
Controls forward/rearward motion and turning. Refer to driving instructions.
Engage to prevent accidental movement when engine is off.
Has three positions: OFF, ON/PREHEAT, and START.
Controls engine speed and blade speed; use FAST for mowing.
Synopsis of available options from the menus: Faults, Service, Settings, About.
Contains a list of recent machine faults. Refer to Service Manual for details.
Contains machine information such as hours of use.
Allows customization and modification of configuration variables on the display.
Lists model number, serial number, and software version of the machine.
Lists total hours for machine, engine, fan, transport, and overheating.
Controls units used on InfoCenter (English or Metric).
Controls the language used on the InfoCenter.
Controls the brightness of the LCD display.
Controls the contrast of the LCD display.
Allows authorized personnel to access protected menus via PIN code.
Lists the model number of the machine.
Lists the serial number of the machine.
Lists the software revision of the master controller.
Lists the software revision of the InfoCenter.
Lists the machine communication bus status.
Steps to access protected menus using the PIN code.
Safety precautions to take before operating the machine.
General safety guidelines for operating the machine.
Safety precautions for handling fuel.
Specifications for diesel fuel, including API, ACEA, and JASO categories.
Details on diesel fuel rating and sulfur content.
Procedure for lowering the roll bar, with safety warnings.
Explains how the safety-interlock system prevents engine start/operation.
Procedure to test the safety-interlock system before each use.
Safety precautions to take while operating the machine.
General safety guidelines for operation.
Safety information regarding the Rollover Protection System.
Specific safety guidelines for machines with a foldable roll bar.
Safety guidelines for operating on slopes.
How to use the deck-lift switch to raise and lower the mower deck.
DPF regeneration during normal operation at high engine speed/load.
DPF regeneration during low engine speed/load, adjusting engine settings.
DPF regeneration occurring every 100 hours or after insufficient assist regeneration.
DPF regeneration requiring the machine to be parked.
Determine hours since last reset, parked, or recovery regeneration.
Setting the InfoCenter to inhibit or allow reset regeneration.
Messages displayed for recovery regeneration requests.
Messages displayed for parked regeneration requests.
Use FAST throttle and adjust ground speed for optimal mowing.
Alternate mowing direction to avoid ruts and aid clipping dispersal.
Use slower ground speed for better cut quality in certain conditions.
Raise cutting height if width is greater than previous machine to avoid low cut.
Adjust cutting height based on grass conditions, avoid cutting more than 1/3.
Raise cutting height for longer or moist grass, then cut again at normal height.
Clean mower underside to maintain cutting quality and prevent fires.
Safety measures after operating the machine.
Safety precautions to take before performing maintenance.
Schedule of maintenance procedures based on service intervals.
Procedure for lubricating bearings and bushings with lithium grease.
Procedure to check the lubricant level in the mower-deck gearbox.
Procedure to change the mower-deck gearbox lubricant.
Safety precautions for engine maintenance.
Specifications for engine oil, including API, ACEA, and JASO categories.
Procedure to check the engine oil level daily.
Procedure for replacing the engine fuel filter.
Safety precautions for the electrical system.
Procedure for cleaning and maintaining the battery.
Guidelines for storing the battery when the machine is not in use.
Procedure to check and replace fuses if electrical issues occur.
Maintain correct air pressure in front and rear tires for proper cut.
Safety precautions related to the cooling system.
Procedure to check the coolant level in the expansion tank.
Procedure to adjust the parking-brake interlock switch.
Procedure to check and adjust alternator belt tension.
Procedure to adjust the neutral-interlock switch for control levers.
Safety precautions related to the hydraulic system.
Procedure to check the hydraulic fluid level.
Procedure to clean the underside of the mower with water.
Instructions for preparing the machine for storage.
Explanation of the warning label and its purpose.
Information about California's Proposition 65 law.
Clarification on the geographical applicability of Prop 65 warnings.
Comparison of California Prop 65 standards to federal and international standards.
Reasons why similar products may or may not have Prop 65 warnings.
Toro's reasoning for providing Prop 65 warnings on their products.
Details the conditions and products covered by the Toro warranty.
How to obtain warranty service and contact information.
Owner's responsibilities for maintenance and adjustments.
List of product failures and conditions not covered by the warranty.
Warranty coverage for parts scheduled for replacement.
Specific warranty information for deep cycle and lithium-ion batteries.
Normal services like tune-ups and filter replacements are at owner's expense.
General terms and conditions of the warranty.
Information about the separate engine warranty for emissions control.
Information for customers who purchased products exported from the US or Canada.
To Next Page