Toro TITAN ZX6020 - Hydraulic Filter Installation; Hydraulic System Bleeding

InstallingtheHydraulicSystemFilters
ServiceInterval:Aftertherst50hours
Every400hours
1.Applyathincoatofoilonthesurfaceoftherubber
sealofeachlter(
Figure53).
2.Turnthelterclockwiseuntilrubbersealcontactsthe
lteradapterthentightenthelteranadditional3/4
to1fullturn(Figure53).
3.Repeatstep2fortheotherlter.
4.Alignthelterguardsovereachlter;refertostep4of
RemovingHydraulicSystemFilters(page41).
5.Securethelterguardswiththe
3screwsremovedinstep4of
RemovingHydraulicSystemFilters(page41)Usethe
threescrewstosecurethelterguards.
6.Addoiltothehydraulicsystemasfollows:
A.Ensurethattheventplugsandreservoircapare
removedbeforeaddingtheoil(
Figure51and
Figure52).
B.Slowlypourthespeciedoilthroughexpansion
reservoiruntiloilcomesoutofoneofthevent
plugholesandstoplling(
Figure52).
C.Installthatventplug(Figure52).
Note:Torquetheplugto20.3N-m(180in-lb).
D.Addoilthroughtheexpansionreservoiruntiloil
comesoutoftheremainingventplugholeonthe
secondtransmissionandstoplling(Figure52).
E.Installthatventplug(Figure52).
Note:Torquetheplugto20.3N-m(180in-lb).
7.Addoilthroughtheexpansionreservoiruntilitreaches
theFULLCOLDlineontheexpansionreservoirand
installthecapforthereservoir(Figure51).
8.Bleedthehydraulicsystem;referto
BleedingtheHydraulicSystem(page42).
Important:Failuretoperformthe Bleeding
the Hy draulic System procedureafterchanging
hydraulicltersandoilmayresultinirreparable
damagetothetransaxledrivesystem.
BleedingtheHydraulicSystem
1.Raisetherearofmachineupandsupportwithjack
stands(orequivalentsupport)justhighenoughto
allowdrivewheelstoturnfreely.
G010333
1
Figure54
1.Jackingpoints
2.Gototheoperator'sposition.
3.Startengineandmovethrottlecontrolaheadto1/2
throttleposition.
4.Disengageparkingbrake.
5.Cyclethehydraulicsystembyperformingthefollowing:
A.Movethebypassleversrearwardandthendown
tolocktheminplace(valveopenposition);refer
toToPushtheMachine(page28).
B.Withthebypassvalvesopenandtheengine
running,slowlymovethemotioncontrolleversin
bothforwardandreverse(5or6times).
C.Movethebypassleversuptounlockthem
andforward(valveclosedposition);referto
ToPushtheMachine(page28).
D.Withthebypassvalveclosedandtheengine
running,slowlymovethedirectionalcontrolin
bothforwardandreversedirections(5to6times).
6.Stoptheengineandchecktheoillevelintheexpansion
reservoir.Addthespeciedoilasuntilitreaches
theFULLCOLDlineontheexpansionreservoir
(Figure51).
7.Repeatstep5untilalltheairiscompletelypurgedfrom
thesystem.
Note:Whenthetransaxleoperatesatnormalnoise
levelsandmovessmoothlyforwardandreverseat
normalspeeds,thenthetransaxleisconsideredpurged.
8.Checktheoillevelintheexpansionreservoironelast
time.AddthespeciedoilasuntilitreachestheFULL
COLDlineontheexpansionreservoirifnecessary
(
Figure51).
42