8
CAUTION!
1.To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.
2.Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the moving parts, turn off
the power switch to stop movement.
Safety Summary
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for
safe handling are included in this manual. All warnings and cautions contained in this manual and written inside or outside
of the printer should be read and understood before handling or maintaining the equipment.
Do not attempt to effect repairs to this equipment. If a fault occurs that cannot be rectified using the procedures described
in this manual, turn off the power, then contact your authorised TOSHIBA TEC representative for assistance.
Safety Precautions
This Owner's Manual and the products (machines) which you have purchased contain indications which should be
observed in order to use the machines safely and prevent harm to yourself and others and damage to property. The
meanings of these indications and symbols are given below.
Read these indications and become familiar with their contents before reading this Owner's Manual.
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
(1) Try to avoid locations that have the following adverse conditions:
*Temperatures out of the specification
*High Humidity
*Direct sunlight
*Excessive vibration
(2) The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution.
NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.
(3) USE ONLY TOSHIBA TEC SPECIFIED media.
(4) DO NOT STORE the media where it might be exposed to direct sunlight, high temperatures, high humidity, dust, or gas.
(5) Any data stored in the memory of the printer could be lost during a printer fault.
(6) DO NOT open the top cover and battery cover during operation. Doing so will stop printer operation.
(7) DO NOT scratch the surface of printed labels or receipt with a sharp object.
(8) Be sure to use a shielded interface cable.
CAUTION!
1.This manual may not be copied in whole or in part without the prior written permission of TOSHIBA TEC.
2.The contents of this manual may be changed without notification.
3.Please refer to your local Authorised Service representative with regard to any queries you may have in this manual.
Keep away from microwave devices.
Communication performance may deteriorate or a communication error may occur due to radio interfearence emitted from
the microwave device.
Since the Bluetooth and wireless LAN use the same radio frequency band, each radio wave may interfere with each other
when they are used at the same time, causing a deterioration of communication performance or a disconnection of network.
If there is any problem with connection, please stop using either Bluetooth or wireless LAN.
Do not use the product on a metal table or near a metal object.
Communication performance may be deteriorated.
GS2100MIP Specification
Standard IEEE802.11 b / g / n
Frequency
USA: 2,412 to 2,462 MHz ; EUROPE:2,412 to 2,472
MHz
Spacing 5 MHz
Channel: USA:1 to 11 ch ; EUROPE:1 to 13 ch
Antenna PCB Trace antenna (built-in module) @2.0dBi
Communication speed/
Modulation
IEEE802.11b : CCK modulation rates of 5.5 and 11
Mbps; DSSS modulation for data rate of 1 and 2 Mbps
IEEE802.11g : OFDM modulation rates of 6, 9, 12, 18,
24, 36, 48 and 54 Mb/s
IEEE802.11n : 1x1 single stream, 20MHz channels
(1x1 HT20), 400/800ns GI, MCS0-7
Data rates of 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65.0, 72.2
Mbps
Receive Sensitivity 802.11b -93dBm ; 802.11g -74dBm ; 802.11n -71dBm
Transmission output 802.11b Typ. 17 dBm (50.12mW)
802.11g Typ. 14 dBm (25.12mW)
802.11n Typ. 12 dBm (15.85mW)
BT800 Specification
Bluetooth version V4.0 Dual Mode
Frequency 2.402 to 2.480 GHz
Maximum Transmit Class 1
Power +8 dBm from antenna "
Receive Sensitivity -89 dBm
Data Rates Up to 3 Mbps (over the air)
Communication distance 3m/360deg (For FP3D specification)
Certification (Module)
US/FCC: SQGBT800, CANADA/IC:
3147A-BT800
(Put on "Contains FCC ID: SQG-
BT800" in certifcation label)
Europe: RTTE 1995/5/EC Annex IV
Antenna specification
PN: AT3216-B2R7HAA, Mfg.: ACX,
Type Ceramic, Gain: 0.5(dBi)
To Next Page
Loading...
Need help?
General