What to do if my Toshiba B-FP3D Printer has EXCESS HEAD TEMPERATURE?
If your Toshiba Printer displays EXCESS HEAD TEMPERATURE, it means the print head temperature reached the upper limit of the operating temperature. Stop printing and wait until the printer automatically restores. If the problem continues, please contact TOSHIBA TEC service representative.
What to do if Toshiba B-FP3D does not print media and status indicator lights orange?
If your Toshiba printer isn't printing and the status indicator light is orange, it means the battery is nearly depleted. Turn off the printer and replace the battery with a fully charged one.
What to do if Toshiba Printer does not print media and status indicator lights red?
If your Toshiba printer isn't printing and the status indicator light is red, it indicates that the battery voltage is low. Turn off the printer and replace the battery with a fully charged one.
How to fix Toshiba B-FP3D when it does not print media and the status indicator blinks in green or orange?
If your Toshiba printer is not printing and the status indicator blinks green or orange, it might be due to a communication error. Check that the interface cable is firmly connected and verify the communication parameters.
What does AMBIENT TEMP ERROR mean on my Toshiba B-FP3D Printer?
An AMBIENT TEMP ERROR on your Toshiba Printer means the ambient temperature has reached the upper limit of the operating temperature. Stop printing until the ambient temperature falls within the printer’s operating temperature range.
What to do if my Toshiba Printer shows HEAD ERROR?
If your Toshiba Printer displays HEAD ERROR, it means a part of the print head element is broken. Turn off the printer and contact TOSHIBA TEC service representative for replacement of the print head.
Why Toshiba B-FP3D Printer print start position is not detected?
If the print start position is not being detected on your Toshiba printer, it could be due to several reasons: the sensor is not adjusted properly (re-adjust the sensor), the sensor is not installed properly (re-install the sensor), the sensor or the sensor filter is dirty (clean the sensor and sensor filter), or the sensor is disconnected from the CPU PC board assembly (connect the sensor to the CPU PC board assembly completely).
What to do if Toshiba B-FP3D Printer power switch does not perform?
If the power switch on your Toshiba printer is not working, it could be due to a power switch failure or a CPU PC board assembly failure. Replace the power switch or the CPU PC board assembly.
How to fix poor print quality on Toshiba B-FP3D Printer?
If you're experiencing poor print quality with your Toshiba printer, it could be due to a dirty print head (clean the print head) or the use of unspecified media (change the media to the specified one).
What to do if my Toshiba B-FP3D Printer received print data but does not print?
If your Toshiba Printer received print data but does not print, several factors could be responsible: * The distance to the host may be too far; bring the printer within 3m of the host or within wireless coverage. * The printer may be in a noisy environment; avoid such locations. * Obstacles might block the radio wave; use the printer in a clear location. * The printer address may be incorrectly set on the host; ensure it’s correctly configured. * The channel setting for the access point or host could be incorrect; avoid interfering channels. * The issue mode may be incorrect; select the correct mode. * The STATUS lamp might be lit or blinking; clear the error.
Contains CE, FCC, and regional compliance statements for the printer.
Essential safety advice for operating and handling the printer and its components.
Information on proper product and battery disposal as per WEEE directive.
Safety and usage rules for Bluetooth and WLAN modules.
Detailed technical specifications for BT800 and GS2100MIP modules.
Technical specifications for label and receipt paper, including widths and lengths.
Guidelines for storing media to maintain quality and handling to prevent damage.
Details on basic specifications, physical dimensions, weight, and electronics.
Information on wireless modules, interfaces, and media supply capabilities.
Instructions for cleaning the print head, platen, strip shaft, and media path.
Guidance on cleaning the printer's top cover and operation panel.
Explains LCD messages, Wi-Fi signal, Bluetooth status, and transmission indicators.
Details on using the POWER, FEED, and PAUSE buttons for printer control.
Step-by-step instructions for loading and unloading the battery pack.
How to charge the battery pack using optional adapters or chargers.
Guide for properly inserting media rolls and adjusting paper guides.
Instructions for preparing and using the optional label peel-off unit.
Guide for attaching the belt clip and optional shoulder strap.
Instructions for USB connection and wireless communication setup.
Common error messages and steps to resolve them.
Solutions for problems like the printer not turning on or communication failures.
General| Print Technology | Direct Thermal |
|---|---|
| Print Resolution | 203 dpi (8 dots/mm) |
| Print Speed | Up to 6 ips (152.4 mm/sec) |
| Connectivity | USB, Bluetooth |
| Operating System Compatibility | Windows, Android, iOS |
| Emulations | TPCL |
| Operating Temperature | -10°C to 50°C (14°F to 122°F) |
| Storage Temperature | -20°C to 60°C (-4°F to 140°F) |
| Memory | 8 MB Flash |
| Supported Barcode Types | 1D and 2D barcodes |
| Supported Media Types | Label |
| Power Supply | Battery pack |
To Next Page
