Why is the operating time short on my Toshiba B-EP2DL Printer even with a fully charged battery?
If a fully charged battery is loaded but the operating time is short on your Toshiba printer, it means the battery life is expired. Load a fully charged new battery pack correctly.
What does it mean when the status light on my Toshiba B-EP2DL is orange and it's not printing?
If your Toshiba Printer is not printing media and the status indicator light is orange, it means the battery is nearly depleted. Replace the battery with a fully charged one as soon as possible.
Why won't my Toshiba B-EP2DL print labels one by one in strip mode or the specified number in batch mode?
If your Toshiba Printer is not printing labels correctly in strip or batch mode, it may be due to sensor issues: * The sensors may not be adjusted properly; re-adjust them. * The sensors may not be installed correctly; re-install them. * The sensors may be dirty; clean them. * The sensors may be disconnected from the CPU PC board assembly; connect them.
How to improve print quality on a Toshiba B-EP2DL Printer?
If you are experiencing poor print quality with your Toshiba Printer, it could be due to a dirty print head. Clean the print head. Another possible cause is using unspecified media. Try changing the media to the specified type.
Why can't my Toshiba B-EP2DL Printer communicate via IrDA?
If your Toshiba printer cannot communicate via IrDA, there could be several reasons: 1. The printer is not turned on. Make sure to turn on the printer. 2. The distance to the host is too far. Bring the printer close to the host, ensuring their IrDA windows face each other within 10cm. 3. The angle of the IrDA window is not proper. Adjust the printer so that the IrDA window faces that of the host. 4. Direct sunlight is interfering with the IrDA window. Avoid direct sunlight. 5. The IrDA window is dirty. Clean the IrDA window. 6. A serial interface cable is connected (GH20 only). Disconnect the RS-232C cable from the printer.
What to do if my Toshiba B-EP2DL does not print and the status light is blinking red?
If your Toshiba Printer is not printing media and the status indicator is blinking red, there are several possible causes: * The media roll may not be loaded correctly. Try re-loading it. * The media cover might not be completely closed. Ensure it is closed properly. * The media might be jammed. Remove any jammed media and reload the roll. * The print head FPC harness or the print head element could be broken, requiring replacement. * The print head temperature may have reached its upper limit. Open the media cover to let it cool down. * A Flash ROM write or erase error might have occurred. Open and close the media cover, or replace the CPU PC board assembly. * There may be insufficient area in the flash ROM. Open and close the media cover, then erase data. * The print mod...
What does AMBIENT TEMP ERR mean on Toshiba B-EP2DL?
The 'AMBIENT TEMP ERR' message on your Toshiba printer indicates that the ambient temperature has reached the upper limit of the operating temperature. Stop printing until the ambient temperature falls within the printer’s operating temperature range.
What does EXCESS HEAD TEMP mean on Toshiba Printer?
If your Toshiba printer displays 'EXCESS HEAD TEMP', it means the print head temperature has reached the upper limit of the operating temperature. Stop printing and wait until the printer automatically restores. If the problem continues, please turn off the power and contact TOSHIBA TEC service representative.
What to do if my Toshiba B-EP2DL Printer says NO PAPER?
If your Toshiba Printer indicates 'NO PAPER,' it means the printer has run out of media. To resolve this, load a new media roll and press the [PAUSE] button.
What to do if the [FEED] button on my Toshiba B-EP2DL Printer isn't working?
If the [FEED] button on your Toshiba Printer is not functioning, it may be because the button is not being pressed completely. Try pressing the [FEED] button more firmly.
Product compliance with EU EMC and R&TTE Directives.
Equipment compliance with FCC Part 15 limits for Class B digital devices.
General, country-specific, and safety precautions for wireless device handling.
Procedures for cleaning the print head, peel-off roller, and platen.
Common error messages and their corresponding troubleshooting steps.
Resolving issues with printer not turning on, battery, and communication problems.
Troubleshooting light printouts and data reception failures.
General| Product Series | B-EP2DL Series |
|---|---|
| Manufacturer | Toshiba |
| Category | Printer |
| Print Technology | Direct Thermal |
| Print Resolution | 203 dpi |
| Media Type | Label |
| Memory | 16 MB Flash |
| Interface | USB |
| Supported Operating Systems | Windows |
To Next Page
