What to do if my Toshiba Printer shows BATTERY TEMP ERROR?
If your Toshiba Printer displays BATTERY TEMP ERROR, it means the battery is extremely hot. Turn off the printer, disconnect the power adapter if connected, and wait until the battery temperature falls within the printer’s operating temperature range.
Why is my Toshiba Printer showing a HIGH VOLT. ERROR?
If your Toshiba Printer displays HIGH VOLT. ERROR, it indicates the battery voltage is abnormal. Turn off the printer, remove the battery, reload it, and turn on the printer again. If the problem continues, please contact TOSHIBA TEC service representative.
What does CHARGE ERROR mean on my Toshiba Printer?
A CHARGE ERROR on your Toshiba Printer indicates an error was detected while charging the battery. This could mean the battery life is at its end. Replace the battery pack with a new one.
Why is the operating time short on my Toshiba B-FP3D Printer even with a fully charged battery?
If the operating time is short on your Toshiba Printer even with a fully charged battery, it means the battery life has expired. Load a fully charged new battery pack.
What does it mean if my Toshiba B-FP3D shows other error messages?
If your Toshiba Printer displays other error messages, it indicates a hardware or software failure. Turn off the printer, then back on. If the problem continues, please contact TOSHIBA TEC service representative.
What to do if my Toshiba B-FP3D printout is too light?
If your Toshiba Printer printout is too light, several factors could be responsible: * The print head could be dirty; clean it. * The media may be improperly loaded; load it correctly. * The media may be past its use date or not TOSHIBA TEC approved; use a new, approved roll.
What to do if my Toshiba Printer shows HEAD ERROR?
If your Toshiba Printer displays HEAD ERROR, it means a part of the print head element is broken. Turn off the printer and contact TOSHIBA TEC service representative for replacement of the print head.
What to do if my Toshiba B-FP3D Printer received print data but does not print?
If your Toshiba Printer received print data but does not print, several factors could be responsible: * The distance to the host may be too far; bring the printer within 3m of the host or within wireless coverage. * The printer may be in a noisy environment; avoid such locations. * Obstacles might block the radio wave; use the printer in a clear location. * The printer address may be incorrectly set on the host; ensure it’s correctly configured. * The channel setting for the access point or host could be incorrect; avoid interfering channels. * The issue mode may be incorrect; select the correct mode. * The STATUS lamp might be lit or blinking; clear the error.
What to do if Toshiba B-FP3D does not print media and status indicator lights orange?
If your Toshiba printer isn't printing and the status indicator light is orange, it means the battery is nearly depleted. Turn off the printer and replace the battery with a fully charged one.
What to do if Toshiba Printer does not print media and status indicator lights red?
If your Toshiba printer isn't printing and the status indicator light is red, it indicates that the battery voltage is low. Turn off the printer and replace the battery with a fully charged one.
General| Print Technology | Direct Thermal |
|---|---|
| Print Resolution | 203 dpi (8 dots/mm) |
| Print Speed | Up to 6 ips (152.4 mm/sec) |
| Connectivity | USB, Bluetooth |
| Operating System Compatibility | Windows, Android, iOS |
| Emulations | TPCL |
| Operating Temperature | -10°C to 50°C (14°F to 122°F) |
| Storage Temperature | -20°C to 60°C (-4°F to 140°F) |
| Memory | 8 MB Flash |
| Supported Barcode Types | 1D and 2D barcodes |
| Supported Media Types | Label |
| Power Supply | Battery pack |
Contains CE, FCC, and regional compliance statements for the printer.
Essential safety advice for operating and handling the printer and its components.
Information on proper product and battery disposal as per WEEE directive.
Safety and usage rules for Bluetooth and WLAN modules.
Detailed technical specifications for BT800 and GS2100MIP modules.
Technical specifications for label and receipt paper, including widths and lengths.
Guidelines for storing media to maintain quality and handling to prevent damage.
Details on basic specifications, physical dimensions, weight, and electronics.
Information on wireless modules, interfaces, and media supply capabilities.
Instructions for cleaning the print head, platen, strip shaft, and media path.
Guidance on cleaning the printer's top cover and operation panel.
Explains LCD messages, Wi-Fi signal, Bluetooth status, and transmission indicators.
Details on using the POWER, FEED, and PAUSE buttons for printer control.
Step-by-step instructions for loading and unloading the battery pack.
How to charge the battery pack using optional adapters or chargers.
Guide for properly inserting media rolls and adjusting paper guides.
Instructions for preparing and using the optional label peel-off unit.
Guide for attaching the belt clip and optional shoulder strap.
Instructions for USB connection and wireless communication setup.
Common error messages and steps to resolve them.
Solutions for problems like the printer not turning on or communication failures.
To Next Page
