How to fix Toshiba B-FP3D when it does not print media and the status indicator blinks in green or orange?
If your Toshiba printer is not printing and the status indicator blinks green or orange, it might be due to a communication error. Check that the interface cable is firmly connected and verify the communication parameters.
Why Toshiba B-FP3D does not print labels one by one?
If your Toshiba printer isn't printing labels one by one in strip mode, or the specified number of labels in batch mode, it might be because the sensors are not adjusted properly (re-adjust the sensors), not installed properly (re-install the sensors), dirty (clean the sensors), or disconnected from the CPU PC board assembly (connect the sensors to the CPU PC board assembly).
Why is my Toshiba B-FP3D Printer showing a PAPER JAM error?
A PAPER JAM error on your Toshiba Printer can occur for several reasons. It may be because the media is not loaded correctly, the media has jammed in the printer, the media has not fed correctly, the reflective sensor does not detect black marks, or the transmissive sensor does not detect gaps between labels. To resolve this, ensure the media is loaded correctly. If jammed, remove the jammed media and reload correctly. Press the [PAUSE] button. If using media with black marks, ensure the correct media is loaded. If the transmissive sensor is the issue, load the correct media or set a threshold.
What to do if my Toshiba B-FP3D Printer says NO PAPER?
If your Toshiba Printer indicates a NO PAPER error, it means the printer has run out of media. To fix this, load a new media roll and press the [PAUSE] button.
How to fix a Toshiba B-FP3D that will not turn on?
If your Toshiba Printer doesn't turn on when you press the power switch, it might be due to the battery pack not being loaded correctly. Ensure you load a fully charged battery pack.
Why can't my Toshiba B-FP3D communicate via USB?
If your Toshiba Printer cannot communicate via USB, it could be due to several reasons. Ensure the printer is turned on. If it's communicating wirelessly, terminate the wireless communication. Also, verify that the issue mode is correct and select the appropriate one.
What to do if Toshiba B-FP3D does not print media and status indicator blinks red?
If your Toshiba printer isn't printing and the status indicator is blinking red, the issue could stem from several causes. Try these solutions: * Ensure the media roll is loaded correctly. * Verify the media cover is completely closed. * Check for and remove any jammed media. * If the print head temperature is too high, open the media cover and allow the print head to cool. If the problem persists, the print head FPC harness or the print head element may be broken and need replacement. Alternatively, a flash ROM write or erase error may have occurred, or there may be insufficient area in the flash ROM, requiring you to replace the CPU PC board assembly or erase data, respectively. Finally, ensure the correct print mode is selected from your PC or handy terminal.
Why Toshiba Printer not turning on?
The Toshiba printer might not be turning on due to several reasons: the battery may not be loaded correctly (re-load the battery correctly), the battery terminal might be disconnected from the soldering part (replace the battery terminal), or there could be a CPU PC board assembly failure or Drive PC board assembly failure (replace the CPU PC board assembly or the Drive PC board assembly).
How to fix poor print quality on Toshiba B-FP3D Printer?
If you're experiencing poor print quality with your Toshiba printer, it could be due to a dirty print head (clean the print head) or the use of unspecified media (change the media to the specified one).
Why Toshiba B-FP3D Printer does not print by radio communication?
If your Toshiba printer is not printing via radio communication, the issue may arise from several causes: an interface PC board assembly failure (replace the interface PC board assembly), a CPU PC board assembly failure (replace the CPU PC board assembly), the interface PC board assembly being disconnected from the CPU PC board assembly (connect the interface PC board assembly with the CPU PC board assembly completely), or a broken FPC cable for the interface PC board (replace the FPC cable for the interface PC board).
General| Print Technology | Direct Thermal |
|---|---|
| Print Resolution | 203 dpi (8 dots/mm) |
| Print Speed | Up to 6 ips (152.4 mm/sec) |
| Connectivity | USB, Bluetooth |
| Operating System Compatibility | Windows, Android, iOS |
| Emulations | TPCL |
| Operating Temperature | -10°C to 50°C (14°F to 122°F) |
| Storage Temperature | -20°C to 60°C (-4°F to 140°F) |
| Memory | 8 MB Flash |
| Supported Barcode Types | 1D and 2D barcodes |
| Supported Media Types | Label |
| Power Supply | Battery pack |
Contains CE, FCC, and regional compliance statements for the printer.
Essential safety advice for operating and handling the printer and its components.
Information on proper product and battery disposal as per WEEE directive.
Safety and usage rules for Bluetooth and WLAN modules.
Detailed technical specifications for BT800 and GS2100MIP modules.
Technical specifications for label and receipt paper, including widths and lengths.
Guidelines for storing media to maintain quality and handling to prevent damage.
Details on basic specifications, physical dimensions, weight, and electronics.
Information on wireless modules, interfaces, and media supply capabilities.
Instructions for cleaning the print head, platen, strip shaft, and media path.
Guidance on cleaning the printer's top cover and operation panel.
Explains LCD messages, Wi-Fi signal, Bluetooth status, and transmission indicators.
Details on using the POWER, FEED, and PAUSE buttons for printer control.
Step-by-step instructions for loading and unloading the battery pack.
How to charge the battery pack using optional adapters or chargers.
Guide for properly inserting media rolls and adjusting paper guides.
Instructions for preparing and using the optional label peel-off unit.
Guide for attaching the belt clip and optional shoulder strap.
Instructions for USB connection and wireless communication setup.
Common error messages and steps to resolve them.
Solutions for problems like the printer not turning on or communication failures.
To Next Page
