What to do if the Toshiba BA410T-TS12-QM-S Barcode Reader shows 'COVER OPEN'?
If your Toshiba Barcode Reader displays a 'COVER OPEN' error, it means a feed or issue was attempted with the Front Cover opened. Close the Front Cover, then press the [RESTART] key.
What to do if my Toshiba BA410T-TS12-QM-S Barcode Reader has a paper jam?
If your Toshiba Barcode Reader is experiencing a paper jam, there are several potential causes and solutions: 1. If the media is jammed, remove the jammed media, clean the Platen, reload the media correctly, and then press the [RESTART] key. 2. If a wrong Media Sensor is selected, turn the printer off and then on, select the correct Media Sensor, and resend the print job. 3. If the Black Mark Sensor is misaligned, adjust the sensor position and press the [RESTART] key. 4. If the media size is incorrect, replace it with the correct size and press the [RESTART] key, or turn the printer off and on, select a matching programmed size, and resend the job. 5. If the Upper and Lower Sensors misalign, align them. 6. If using media with Black mark and Gap, and 'CALIBRATE' is set to 'ON ALL' o...
What to do when Toshiba BA410T-TS12-QM-S shows 'LOW BATTERY'?
When your Toshiba Barcode Reader displays 'LOW BATTERY', it means the voltage of the Real Time Clock Battery is 1.9V or less. Hold down the [RESTART] key until “RESET” is displayed. To continue using the same battery, set the Low battery check function to OFF and set the date and time. Note that the date and time will reset when the power is turned off.
What to do if my Toshiba Barcode Reader shows 'RFID ERROR'?
If your Toshiba Barcode Reader displays an 'RFID ERROR', it means the printer cannot communicate with the RFID module. Turn the printer off, and then on again.
What does 'RFID WRITE ERROR' mean on my Toshiba Barcode Reader?
The 'RFID WRITE ERROR' message on your Toshiba Barcode Reader indicates that the printer failed to write data onto an RFID tag after multiple retries. Press the [RESTART] key.
What to do if Toshiba BA410T-TS12-QM-S says 'MEMORY FULL'?
The 'MEMORY FULL' message on your Toshiba Barcode Reader means saving failed due to insufficient flash ROM capacity. Turn the printer off, and then on again.
How to fix 'FORMAT ERROR' on Toshiba BA410T-TS12-QM-S?
The 'FORMAT ERROR' message on your Toshiba Barcode Reader indicates an error occurred while formatting the flash ROM. Turn the printer off, and then on again.
What does 'EXCESS HEAD TEMP' mean on Toshiba BA410T-TS12-QM-S?
The 'EXCESS HEAD TEMP' error on your Toshiba Barcode Reader indicates that the Print Head has overheated. Turn off the printer and allow it to cool down for about 3 minutes.
What does 'SYSTEM ERROR' mean on my Toshiba BA410T-TS12-QM-S?
A 'SYSTEM ERROR' on your Toshiba Barcode Reader can be caused by several factors: * The printer is used in a noisy location, or near power cords of other electrical appliances. Keep the printer and interface cables away from noise sources. * The printer's power cord is not grounded. Ground the power cord. * The printer shares a power source with other electrical appliances. Provide an exclusive power source for the printer. * The application software on your host computer has an error. Confirm the host computer operates properly.
What causes a 'RIBBON ERROR' on a Toshiba Barcode Reader?
A 'RIBBON ERROR' on your Toshiba Barcode Reader can occur for the following reasons: * The ribbon is not fed properly. Remove the ribbon, check its status, and replace it if necessary. * The ribbon has run out. Load a new ribbon and then press the [RESTART] key.
General| Model | BA410T-TS12-QM-S |
|---|---|
| Type | Barcode Reader |
| Scanning Technology | Laser |
| Resolution | 203 dpi |
| Maximum Print Width | 104 mm |
| Connectivity | USB |
| Print Method | Direct Thermal / Thermal Transfer |
| Supported Barcodes | 1D barcodes |
| Operating Temperature | 5°C to 40°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 25% to 85% non-condensing |
| Interface | USB, Ethernet |
Covers printer installation and power connection procedures.
Instructions for loading media (labels/tags) and ribbons.
Steps for connecting to a host computer and turning the printer on.
General guidance on routine maintenance and cleaning schedules for the printer.
Lists common error messages, their causes, and recommended solutions.
Addresses common operational problems and their solutions.
Step-by-step guide for safely removing jammed media from the printer.
To Next Page